How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Hi,
Is it true to say you have two modem firmware streams: 1.1.X and 1.2.X? Are these two kept in sync in terms of GNSS improvements? I notice the 1.2.2 release notes mention...
Hello,
I want to measure current consumption of nRF9160 of the Thingy 91 with the Asset Tracker application in PSM mode without GPS. For that, I added to the function modem_configure...
Hi,
Browsing the API I only saw Enhanced shockburst support. I need air compatibility to an old 250kBit plain Shockburst communication. No auto ACK and no auto retransmit...
I have run up the CLI example to test as we will require some command line interaction and why reinvent the wheel?
I run up the example with USB enabled and UART disabled...
Hello Nordic,
I try to establish communication between an ATmega328 based board an an Arduino Nano, so far without success. The goal is to improve a RF433 "Wire". 3 weeks...
Dear All, I am using the ADC to measure 3 voltages applied on different ADC inputs and 3 different channels. My ADC configuration looks like this: And this is how I am performing...
Hi,
I recently acquired the nRFgo starter kit and nRF2724 rev 2.1 and the nRFgo development kit. I have downloaded all of the supporting software that were found here...
I have the latest nRF Connect for Desktop.
After I install "nRF Connect SDK v1.4.99-dev1" in Toolchain Manager I don't have an "Open IDE" button.
I've tried uninstalling...
I am adding JLINK_MOITOR.c and JLINK_MONITOR_ISR_SES.s and add write
#if CONFIG_JLINK_MONITOR_ENABLED NVIC_SetPriority(DebugMonitor_IRQn, _PRIO_SD_LOW); #endif
at starting...
Hello everyone,
I'm trying to develop an application with BLE, using an example as a base.
The advertising is good, well configurated, I can edit manufacturer specific...
I am currently using Mesh SDK 4.2.0 and I could successfully write and read reliably from the flash using a second flash manager instance used in parallel with the flash manager...
HI，All:
the softdevice.hex has inlcuded the bootable/strat code,as the figure below ,how to separate the bootable code from the hexcode?
in the SEGGER IDE:
in...
Hello,
I am working on nRF52820 custom development board with nRF5 SDK 17.0.2. I am using FreeRTOS and I experienced a lot of problems with compiling a simple project. I...
Hi,
Currently I work on an NRF51 DK, by mistake I replace my bootloader by and .hex or .bin file with a drag and drop.
The LED 5 don't blinking and my computer don't...
Hi Dev zone,
I am working with the mqtt sample program using NCS1.3.0 and with a Nordic Thingy91.
I am able to publish and subscribe to the data , and I am using Mqtt...
