I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I am trying to connect my thingy91 and preform an MCUBoot. This is not working and i get the following error code: Errorcode: CouldNotCallFunction (0x9) Lowlevel error: INVALID_OPERATION...
Excuse me, I use BSP_EVENT_KEY_0 to get into the sleep mode, however, it will go to the NRF_BREAKPOINT_COND and then reset the device;.
case BSP_EVENT_KEY_0:
SEGGER_RTT_printf...
I have developed data loggers based on nrf52840,it uses nus service,max payload is of 240 bytes,the device stores 30kb data in a spi memory.we have a custom built android...
Dear community, as already mentioned here https://devzone.nordicsemi.com/f/nordic-q-a/30622/nrf_cal_set_time-setting-issue-for-2100-year/121167 Im wondering how do you deal...
Hello. I need to calculate the RSSI value from the module nRF9160. I am using the nRF9160 DK 0.8.2. From the AT reference guide, there are two commands: AT+CESQ and AT+CSQ...
The new Bluetooth specification 5.2 will support transmission of audio data in a so called isosynchronous burst mode to external, BLE capable speakers, opening up a long asked...
Hi,
We are having some issues with the values obtained via ADC readings. We have a few designs using the nRF52840 where the analog reads from sensors are not stable. To...
Hi,
We used nRF52840 Dongle to receive BLE peripheral device 240Bytes notification. The connectivity that "Bluttooth low energy" (nRF connect) programmed can received 240Bytes...
Hi,
I am using NRF52810 controller, The power consumption of my board in SLEEP MODE is 200uA . According to datasheet the ideal current in sleep mode is 3 uA.
In advertising...
Hi,
I use SDK16 ble sec-bootloader and merged application image together followed by the guide of the website
unfortunalately , after flahsing fw_all_s140.hex to device...
Hello,
Question regarding GPS power consumption numbers in the nRF9160 data sheet (V2.0)
Section 5.2.1.16 GPS Current Consumption:
Are the current consumption numbers...
Hi,
I would used a RTC calendar (Years, month, day, hour, minute, second).
The smartphone connect to the nrf51822 and updates the date and time.
The nRF51822 must perform...
Hi,
Is it safe to call nrfx_spim_init() multiple times with and without a handler without calling uninit() in between?
I have an SPI device that needs a sequence of steps...
I keep seeing NOT_AVAILABLE_BECAUSE_PROTECTION errors on all sub-programs of nRF Connect when attempting to program the associated firmware (RSSI viewer, Bluetooth Low Energy...
Hi,
I am trying to create a Mesh network using CCT controlled lights and switch.
I am using nRF52-DK, I want to use one of the button for two functionalities i.e storing...
