I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello, I am creating a peripheral with a totally custom set of services and characteristics (it will only talk to our custom central device). I've adapted the examples and...
Hello, in my application (adapted from ble_app_uart peripheral example of SDK 16.0) I am starting advertising using
err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST...
Hi.
I'm working with both custom board based on nrf52840 and nrf52840-dk.
I just moved from the app_uart api to the abstract serial api.
I have noticed that when an...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_beacon’.
1) ‘ble_app_beacon’ will only broadcast...
Hello Devzone:
Would I be correct if I assume enabling APPROTECT should prevent writes into UICR? - for other readers, NO, IT CANNOT PROTECT AGAINST SOFTWARE READS/WRITES...
I am in the process of adding central functionality to ble_app_buttonless_dfu on a PCA10056.
When I call nrf_ble_scan_filter_set, the resulting builds debugging is broken...
Hi, I want to use the ADC peripheral (SKD16) and I am looking for the most energy-efficient way of doing this. I design a prototype that will be based on nRF52840 IC and will...
For a temperature sensing application, I am trying to implement a TWI interface with a TMP116 temperature sensor. I am using Keil uVision 5 to write the program. I have been...
I am attempting to port a BLE application to the nRF52840. The original application used a standard HCI serial interface so I am trying to adapt that to use the Nordic SoftDevice...
Calling the lte_lc_connect() function eventually leads to the code breaking on:
fault_s.S line 104
#elif defined(CONFIG_ARMV7_M_ARMV8_M_MAINLINE) /* force unlock interrupts...
Hi I am using NRF52 board to interface analog sensor and this board further transmit the data ro sink node. I am using saadc example but unable to get callback or my interrupt...
We have a set of custom boards I am working on debugging. I was able to get our software onto the device via nrf jprog tool by uploading a merged hex file (with SD + bootloader...
Hello,
I would like to turn off the logging to UART0 completely on my custom device.
In the past, I have been able to do this using various config options and reduce the...
