Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Hi, Everyone
I use sdk15.2 & nrf52832
I am doing a test to read the slave address in TWI
There is one slave device on the board and the slave address is 0x68
I used three...
I am working with SPIS example ( sdk version 15.3). SPI master send data regulaly. For example, it sent 5ms cs low, but there are only two bytes transferred, the first byte...
Hi,
I'm working on a project that is using the the freeRTOS and I want to use the NFC pins P0.9 P0.10 to drive SOFTWARE SERIAL UART with a timer like TIMER1, when I try...
iPhone 8 Plus with nRF connect App[iOS], does not shows BLE 5 beacon in scanning, it only scanning BLE 4 beacons, In Spec of phone it shows it support BLE 5
nRF connect...
Hello,
I follow the nRF Connect SDK on a Windows 10 x64 computer and it's a crap. I get a lot of errors like this one. It's so crappy that I doubt that I will continue with...
Hello,
I am not able to send a command from the BLE (52810) to a DSP over UART which are on my custom board. I have modified a program that uses UART for logging purpose...
The s132_nrf52_7.0.1 documentation says: Call stack: The SoftDevice uses a call stack combined with the application. The worst-case stack usage for the SoftDevic e is 1.5...
I am doing a program based on Current Time Application example. But I have a few questions, so I hope you can help me. First, I am using Battery service together. By the way...
Hi,
In our current project we use nordic NRF52832 ble to send some data(~200 Byte / packet) to host, we expect each transmission to be done within 10ms, but results from...
Hello. nRF52 A custom board is being developed. I want to use Crypto Chip Pulse to encrypt. Pulse_Out of Crypto Chip is connected to P028/AIN4. In order to measure Pulse,...
I'm using \nRF5_SDK_15.3.0_xxxxx\examples\peripheral\usbd_ble_uart example to use two communication links. Missing echo on the USB virtual COM is a small frustration. I've...
Hi NordicSemi
I have a project where we receive data via the UARTE. To avoid missing data caused by higher prioritized tasks we want to use the DMA facilities.
nrf52832...
Hi,
i want to flash programs with the Segger Embedded Studio to my Thingy 91. I already am able to flash hex files with the nRF Programmer to the thingy 91. I installed...
In addition to (obviously!) a 52811 chip and a BLE beacon, what additional hardware would one need for reasonably accurate location tracking of a BLE tag/beacon? I'm generally...
Hello Devs,
I have enabled NRF_LOG in my project, but I would like to disable it in, for example, the main.c file, but keep it working in others files.
at the moment...
