Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi
I was wondering if it's possible to scan for both 1MBPS and CODED at the same time, or should I initiate 2 different scans.
using this configuration initiates error...
Hello,
we developed our electronics with your chip nRF52840, but we have problem with communication throught BLE. We tried our firmware on dev kit with this chip. It was...
Hello,
I am looking for wireless communication solution between two devices with a maximum distance of 5-10m for controlling a speed of the electric-assisted vehicle (basically...
Hi,
I use SDK 12.3.0 with PCA10040 board, and try running experimental_ble_app_buttonless_dfu. It works fine when I use Keil to compile, but doesn't when use GNU. I open...
Hi,
I've tried connecting to the nRF52840 Dongle using nRF connect as explained in : ://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.tools%2Fdita%2Ftools...
Hi, I've been trying to build a custom characteristic and so far I can display a single digit number on my BLE app. My update value function looks like this:
And my add...
I am using SEGGER Embedded Studio to program the nRF51822 module. When I was going through the manual for setting up the environment for SEGGER Embedded studio, I found that...
I want to use a buzzer on my board.
The environment in use is below. · SDK15 · Nrf 52 · Nrf 52832_xxaa · S132_nrf52_6.0.0_softdevice.hex
My start is "nRF5_SDK_15.0.0_a53641a...
Hi support team,
I'm using a PDK(PCA10056) with nrf52840 and SDK 15.0. Recently I was developing a BLE bootloader for DFU OTA.
Since the ble bootloader was depended on...
Hi
I have been trying to get example ble_app_hrs to run after compilation on my 52832 dev board (pca10040).
The specific example is: C:\Keil_v5\ARM\PACK\NordicSemiconductor...
Hello,
after migrating from SDK14.2.0 to SDK15.0.0 I was suddenly unable to connect my central and peripheral devices. After looking into it with a Bluetooth sniffer, I...
Hey, I want to create a Mesh Monitor, to do this I want to create the follow setup:
Mesh consist of Several servers with Heartbeat message Tx/Rx enabled send periodically...
Hello,
I'm experiencing some problems reconnecting an iOS device (possibly same thing on Android) to my peripheral in the background. This happens most of the times after...
I'm using S140 6.0.0 and associated MBR on an nRF52840 with a custom boot loader derived from the nRF5 SDK 15.0.0 examples.
I'd like to perform some custom actions as soon...
Kindly give suitable example or suggestion for Eddystone Relay / Rebroadcaster. I have checked on Beaconing example but it could not rebroadcase eddystone beacon.
