I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi,
How can I know the value of the interval and scan window for an nRF51 dongle? Is there any way to change these values? W hat is the valid range for both parameters ...
Dear Nordic Team,
Thanks for supporting.
Currently i am work with secure DFU as per this link: https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics...
Hi guys:
I was confused with the problem of "re-pair".
The condition is my device can only bond one phone (I was set the DEVICE_MANAGER_MAX_BONDS to 1).
Then I successful...
HI, I have nrf52832 and I am using latest SDK 14.2.0. I am using FDS and the problem is that before setting up BLE fds_record_write works fine but after setting up BLE all...
Hi there..
I've recently jumped back on development of a board I had made a while ago but have forgotten everything and am starting from scratch as computer was reformatted...
Hi,
I am trying to use nRF52840 boards but I am not able to write on them using JLinkExe nor nrfjprog. However, when drag-and-drop-ing a built example application, it works...
I want to use the radio interrupt to receive data, but I only entered the interrupt once at initialization, and I can't enter the interrupt again. But use the commented out...
Hi,
I'd like to know: when using Buttonless Secure DFU Service without bonds, wich is the proper way to prevent a central device to s et a new advertisement name for the...
Hello,
I've got some trouble using Nordic Uart Services,
I am using ble_app_uart example and after connection receiving bulk data from mobile app & sending it on UART...
Hi,
I have build pc-nrfconnect-rssi accodring to instructions. Though the locally build version responds very slowly compared to the officially installed version. No matter...
I am using a nRF52832 and v14.2 of the Nordic SDK. I have a question about the PWM Driver. I have the pwm driver working and driving an LED, but it is unclear to me how to...
Hello!
I am currently developing an application for the nrf52832 using Segger Embedded Studio as my IDE.
The application is not utilizing any softdevice but I would...
Hi,
We are using an nRF52832 with Soft Device S132 in a project. It has been requested that we should advertise as connectable with our own service and characteristics,...
Hi
In the NRF_MESH_PROV_EVT_COMPLETE event, I call
ERROR_CHECK(dsm_address_publish_add(m_next_unprov_address,&m_device_address_handles[m_next_unprov_index])); ERROR_CHECK...
Hello,
I want to be able to toggle blocking RTT output when using the log module.
Before in SDK13 I could just set SEGGER_RTT_CONFIG_DEFAULT_MODE to 2 in the sdk_config...
