Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
What is the best way to go about implementing secure reads/writes to the NRF52 NFC tag? I noticed there didn't seem to be any built in security functionality in those areas...
I am attempting to use nrf_drv_adc.h in a project where I am splitting up my methods across many C files and, to my surprise, nrf_drv_adc.h does not have any include guards...
Hello,
I received the above error using NRF5 SDK 12.2. I have modified "nrf_drv_config.h" so that it reads #define TWI0_ENABLED 1 . Also, I put #include "nrf_drv_config...
Using nrf52 DK , SDK 12.2 , and armgcc.
I want to use BLE_UART but I also want to bond.
I started with the BLE_UART example code and added peer manager and FDS.
I...
I've been trying to track down a bug where a couple of my Central test devices, a Nexus 5 and 7 (Android 6.1), won't send a connection request to a peripheral they're bonded...
Hi
I have a problem on testing the HRS examples on SDK12.2.0.
When I use a android phone, running on version 6.0, using nRF Toolbox version 2.2.1 App, to connect to the...
Hi!
After reading nRF24L01 product spec, I'm really unsure:
Spec. says: "The input signal should not have amplitudes exceeding any rail voltage."
"rail voltage" it's...
Update 1/27/2016
Just reviewing again the pins + schematic; I am using the following pins:
SCK P0.07
CS P0.08
MOSI P0.06
MISO P0.05/AIN3
Looing at the...
After i test a lot of possible configurations for nrf24L01+ based on the documentation, i didn't come to the right setup for all the nRf24L01+ registers to send data from...
Hi,
I'm using Windows and I am following this tutorial.
I am at the point where I need to write make at the example project.
I get this error
as warned in the...
Hi,
I'm trying to get a general idea of how the radio will perform near the bottom end of the supply range.
Our product concept is currently designed on a system voltage...
Hi,
I stuck on SOFTDEVICE_HANDLER_INIT in example code on nRF DK PCA100028 within debug.
It is example code from SDK 7.1.
How Can I solve this?
Why Nordic's SDK...
Hello,
I am developing an an system and I am at the stage of optimizing for power.
I using NRF6707 ( Very helpful !!) to measure current.
I cut SB9 of NRF52 DK and have...
