I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately,which does not success. With setting radio configuration: TXPower,frequency channel...
Hello, I'm trying to get an ANT+ peripheral example to work on an Adafruit nRF52832 breakout module. I'm using the 15.0 SDK, SD S212 and SES with a J-Link to program over...
Hi,all,
Now I am using nRF52832 to develop a Tire Pressure Monitoring System ,but I serached the ANT website and found that " a TPMS profile is "in the works". ANT+ members...
hi
i need to test the BT OTA test ( total radiated power (TRP), total isotropic sensitivity (TIS)
https://www.mwrf.com/test-measurement/ble-antenna-testing-helps-optimize...
Hello, maybe my answer didn´t get to you correctly. Referring to my post 10 days ago, I am still stuck controlling the joining procedure .
https://devzone.nordicsemi.com...
HELLO
I would like to know how to test RF for nrf24l0.
Of course, the RF test I'm talking about is frequency modulation for KC certificate
Previously, nrf24le1 was...
Hi,
Just to be clear, you are looking for reference DFU controller firmware for the Host MCU, in order to upgrade the firmware on the nRF52832。
I also need this feature...
Hello Developers,
I have configured a mesh network where I have a gateway node and multiple relays to relay messages from End nodes (sensors)
My question is the following...
Hi. I am working with nrf52832 trying to get Bluetooth and UART and a I2C peripheral working at the same time. I had a working version of the I2C peripheral and UART working...
hi.......
i need to run the program continuously using timer ......and want to check the data every one minute how to do that
i have seen timer example .. i am confused...
I am using nRF 5 SDK v 14.2.0.
I'd like to change the tone of the buzzer, how can I do it?
I'd like to make the following three settings.
Treble (+ 1 kHz), normal (+0...
HW: nrf52840
SW: nRF5_SDK_15.2.0_9412b96
source code: blinky_rtc_freertos example
Q1:
I read freeRTOS xtaskcreate operation on the web, it seem that I just need to...
Hi,
I am using Segger IDE.
I encounter error undefined reference to `nrf_drv_rng_init' .
I have include the below header file;
#include "nrf_drv_rng.h"
I already...
Happened when I occasionally compare the NRF_TWIM_Type struct in nrf52.h with the TWI registers (table 127) in nRF52832 Product Specification v1.4, there are many differences...
Will there be an HTML version of the nrf52832 spec document?
I hope Nordic is not expecting me to manually browse through a 550 page pdf document. I regularly use the infocenter...