Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
There appears to be a conflict between ble_advertising and broadcasting while connected. If connected, the ble_advertising state machine still gets TIMEOUT messages from the...
I am working on light switch demo of mesh SDK 2.1.
I am using nRF52832 board, SDK 15 for softdevice and segger embedded studio for programming the nRF52832.
I programmed...
Hello everyone,
I want to develop an android app, which is able to control multiple LED Lamps in a Mesh Network.
There is an app for provisioning provided by Nordic. Is...
Hi,
When I call sd_ble_gattc_read , I receive the BLE_GATTC_EVT_READ_RSP event very shortly after -- as expected. Within the event handler (registered with the Soft Device...
Hi,
I am considering using baluns instead of discrete components next to my nRF24LE1 QFN-24 chip since board space is at premium.
In application note AN4111 regarding...
I am new to Nordic and have a simple question. I followed the instructions about setting up manufacturer specific data with BLE_Template example here: https://devzone.nordicsemi...
in the middle of the code the MOSI change from idle low to high and resulting in writing 0xFF while reading over MOSI, resulting in getting wrong data. how can i change it...
Using SDK 15.0
Example project: examples/dfu/secure_bootloader/pca0040_ble/ses
Segger Embedded studio V3.50
File main.c line 52
#include "uECC.h" <------ "No such...
chip：52832
sdk：12.3 ble_app_template
when I measure the sleep current consumption use the nordic PPK
I found there is a 30ua peak in every 20ms，could you please tell...
I have some questions to Bluetooth mesh.
1. If I have a mesh Network is it possible to have a connection to a device over all the nodes? Or does mesh just support brodcast...
Hello!
I am a beginner.
I am trying to communicate with the SD card with SPI using nrf 52832.(BLE Nano v2)
I am using fatfs of nRF5_SDK_15.0.0_a53641a. I am writing...
Hi ,
SDK：15.1.0
example：proprietary_rf \ esb_ptx
Because there is no UART function in the example, I want to add it.
The picture is everything I added, is it missing...
Hi Devzone team,
In our SDK, say SDK15.0, there is a head file called "sdk_config.h". It contains a line which looks like below:
// <o> NRF_SDH_BLE_GATTS_ATTR_TAB_SIZE...
WIth the upgrade to the new SDK, registering the callback handlers has been made more difficult to figure out.
The .sdh_ble_observers, .sdh_soc_observersers sections are...
