I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hi,
I bought the nrf51822 chip itself, and created my own board. Now, can I still download the nRF51 SDK as per nAN-29?
I am stucked with the download page asking for...
Guys
I came over from the Arduino forums, I am searching for a new RF chip to use for a project i am working on but dont know which chip to pick. My application requires...
I want use uart to debug my ble program ,
In the devzone I found this and this to meet my need , but when I conditional compilation UART code into hex, I can not find my...
Hi All,
I am trying to use the HRM_RX sample code with my Linux PC side application. but i am not able to receive any UART RXD interrupt on nRf51422. I checked PC is sending...
We are developing a BTLE perihperal product using nRF51822 chip. But we would like our product can be up-gradable. So we will need a Bootloader (by UART or other interface...
while creating a Makefile for DFU, for BLE DualBank only, I'm getting some odd errors:
../bootloader_util_arm.c:19:1: error: 'at' attribute directive ignored [-Werror=attributes...
SDK v5.1 /v4.4.2
Keil 4.73/Keil 5.1
delay function seems doesn't work well in new version of keil. But I need it to bebug and flash nRF51822 with new keil.Need your help...
I would like to use an nRF8002 in a proximity detection application.
I would like to be able to send a request/command to the device to start a continuous or rapid transmit...
This may be an obvious question, but I wanted to make sure that my assumptions are correct.
The nRF51822 is able to use an external 32kHz crystal oscillator for its low...
In the 51422 Prod Spec v2.0 it states that “high performance RF capacitors” for the X7R decoupling caps should be used.
Is High performance RF equivalent to a “High...
Hi,
I am trying the Direct Test Mode (DTM) function integrated into the nRFgo application. I am using the nAN-34, Dev Kit User guide, and help (F1) in nRFgo as documents...
I use DK usb dongle to catch data from my ble device , but I can only catch the broadcast data . When the ble device is connected to PC ble dongle , I can't catch data any...
I have Olimex Mod-nRF 8001 Module which i bought it from here . It has break out the RDYN,REQN,MISO,MOSI,SCK and reset pins. My question is can i connect RDYN and REQN lines...
