Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi All,
Please correct the following in my understanding. Also , i am planning to build a
remote controlled device using a PWM output. How does ATT,GATT and GAP affect/influence...
My board works most of the time are very good，but one time i power down the board when ble connecting and data transmitting，the board can't work when power on.and i can't...
Posting this as separate question as it got no traction in the other thread:
Why are there many of the same include files in the DFU example directory as in the S110 7...
Hi all,
this is not a question per se but rather a warning to those who are attempting to debug Flash related operations with the SEGGER J-Link GDB Server (v4.84a for Linux...
hi i use pca10056 board with segger embedded studio
i currently facing a bizzarre problem with my project
i use adc function and nus service and low frequency clock
...
Hello i realize the nRF24L01P is NRND. Curious if you are able to answer w/out too much work as to whether one of the other nRF devices allows access to the radio to use the...
Hi:
I set up a fresh install of the NRF Connect Extension Pack in VS Code on my MacBook Air M4 and was able to build and flash the Blinky demo to my nRF52840DK. The issue...
Hello, this ticket addresses three issues:
1. After installing nrfutil with subcommands device and toolchain-manager and sdk-manager, into %USERPROFILE%\.nrfutil, everything...
Hello,
Since our Product Launch we have gotten feedback that pairing with some (but not all) Apple devices is a significant problem. Even through several attempted fixes...
After upgrading nRF Connect SDK from 3.1.1 to 3.2.1, our fixed regulator stopped working. We are on nRF54L15. Tracking it down further, this seems to be some sort of GPIO...
Hi,
I am porting a product from SDK 15 to SDK 17 and to Nrf Connect.
We need to maintain code combability as far as possible between products using SDK 15/17 and products...
I'm creating a system test for manufactured units and if it's OK I would like to set a permanent flag in an area that will not be erased if I erase flash at a firmware update...
nrf sdk 17.1 example:peripheral/uart/pca10040 I attempted to use P0.9 and P0.10 on the development board to set up a UART serial port for data transmission and reception ...
Hi,
I am on NCS 2.9.0, I have tested lesson 5 exercice from NRF Intermediate course about BLE DFU, I have some questions about it:
- with mcumger, is there a way to update...
Hello,
We have a custom board we are developing on that uses the nRF54L15 MCU. The board has some LEDs that we were hoping to drive using PWM, but these are connected to...
Hi all
I have some trouble with a new batch of nRF9151 chips.
The old one had the Firmware: 2.0.2
The new ons have the Fimrware 2.3.5.
My application does no longer...
Hello
I tried to test OTA function with smp_svr example.
I want to use the external flash mx25r64 on nrf54l15-dk(v0.9.3) to store update Firmware over BLE. SDK version...
Hello,
I have some unclarities for the APPROTECT mechanism on NRF9151.
Basically, I had a misunderstanding of the involved CONFIG features, and as a result I used CONFIG_NRF_APPROTECT_LOCK...
Hello,
I’m using an external NFC reader/controller (NXP PN7160A1HN/C100E) connected via I2C to an nRF52840 module (Raytac MDBT50Q-1MV2) on a custom PCB. (Programming is...
