Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello Community / Nordic How can I have a boolean property in my mp2723 device driver devicetree dts or overlay. I am using NCS v2.2.0 in MS Windows 11 with VSCode 1.17.2...
Hello!
Using nrf_gpio.h enables P0.00 port control, but using app_timer.h together makes port control impossible.
I don't know if the code I wrote is the problem or...
I am using zephyr 3.1.0 and i build blinky pwm and rtc code from zephyr but it is not building i am using nucleo_u575zi_q board but in dts of board pwm and rtc is not there...
I modified the nrf9160 https_client sample to make a GET request to a web server and retrieve a JSON response. Unfortunately the rec_buf always ends up with an HTML response...
Hello everyone!
I've been struggling to get over this error when attempting to use an augmented Thread project based on the thread_mqtt_sn_client_publisher example. Would...
According the nordic documentation of the AT command +CEINFO, the value of CINR is in dBm.
Other source (outside Nordic) mention dB as common unit, e.g. LTE signal quality...
Hello everyone,
I'm trying to display internal sensor on NRF51422-DK (PCA10028) on my Android phone (v.12). I'm using Keil for programming and nRF Toolbox to see UART results...
ble_gap_addr_t xyz;
sd_ble_gap_addr_get(&xyz);
/**@brief Get local Bluetooth identity address. * * @note This will always return the identity address irrespective of the...
Hello, I have three questions that i could not clarify in an adequate amount of time via Google and DevZone.
Setup: I am working on a custom board equipped with nRF52805...
Good day
I am trying to use lwm2m_engine_set_float on the lwm2m_client sample to change the sensor value.
Referring to the above link, the sensor value is set in the...
I am trying to evaluate transitioning a product from the NRF52840 to the NRF5340, but we have a critical feature that uses specific functionality of the PPI. It seems that...
Trying to integrate memfault SDK to nRF SDK 17 segger embedded studio. But couldn't understand the below section. Can someone help with passing flags to linker and also adding...
hi,i use SDK17.02.
l use ESB RX mode, I need send the ack payload data, and I can only write it for 8 times. After I write it for 8 times, I use nrf_esb_flush_tx() to clear...
I am building a Thread Coprocess using the nRF Thread Coprocessor template . Everything seems to work fine except when I use the OPENTHREAD_MANUAL_START=n config in the prj...
