NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
I want to flash a firmware on my nrf51822 module I was trying an example from Nordic, I concatenated the bin file with the s110 file and it worked fine. Now, when I went ahead...
In the nRF8001 Product Specification, section 7.1.5 it states:
"The maximum length of an event packet
is 31 bytes, including the length
byte."
In the headers...
Has anyone seen more than 3 notify packets per 7.5ms connection interval?
I am seeing 3 and am wondering if this is a fault of the way my app is working.
My Setup:
Nordic is the Server, Android is the client.
I have read many, many forum posts about doing long reads/writes. Virtually everyone says you cannot do long writes...
I am trying to connect more then one device to nrf51822 HID.
How can i pair more then one device ?
How can i delete paired device from nrf51822?
Thanks
Recently ran nRF Master Control panel on android and found "Read remote RSSI" button. Is data got from device in some way or simply measured by androd phone ble radio module...
I would like to write to multiple characteristics in a loop but the second call to sd_ble_gattc_write() causes a NRF_ERROR_BUSY error. From reading the documentation, I should...
Hi all,
I am working with PCA10028. I have a peripheral and central both are devices with no display and no keyboard. both peripheral and central device are under our control...
Hi,
I am using nrf51822 with s110 softdevice version 8.0.
Is there any way i can know the state of my radio at some point in the code execution?
In short I want to access...
As explained by electronut in his Blog and Lijun here , it is possible to program an External nRF51822 board using the SWD interface of the nRF51-DK.
But what about a custom...
I have a project, and nRF52832 it 's good chip for me, because it has NFC/ bluetooth communication.
I would like to know if nRF52832 can pilot epaper display. nRF52832 does...
Hi,all. i face a problem. the office DFU flowchart is device reset--->bootloader --->upload firmware to device ---->device reset.i want to implement as follow: upload firmware...
Dear all
We did nordic beacon board in that we not able to flash the device
We are checked core voltage 1.2V and 1.7V are coming .But i want to confirm external CLOCK will...
Hi,
I want to change the interval time of 51822 dongle with the instruction here devzone.nordicsemi.com/.../
The default value is 100ms as following
#define NON_CONNECTABLE_ADV_INTERVAL...
Hey guys,
I’m working on an nRF51822 design where I’d like to check the value of a GPIO at Power-ON, then either shutdown, OR start the BLE stack and do BLE stuff. I really...
