Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately,which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am using two nRF52840...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am using NUS to work with...
During my test of the nrf5340 audio application which in the V2.6.0 SDK , Because of i need to store at least 13K data to the flash.
But when i build the project, i found...
I've got a project based on NCS v2.6.0 using a nRF52840 as contained in a Fanstel BT840F module.
With help from you all (thank you!), the software works. Bluetooth and PWM...
Hello!
I have a custom board with an nRF52805 on it and I am simply trying to run the Zephyr blinky example and verify I can see a GPIO toggling as my first step. I installed...
Hello all,
We're on the initial stages of a design that requires Wifi (ideally) in a very challenging environment, where in the worst case scenario the temperature could...
Hello,
we run an application on a custom board with nRF52840 powered by an external power supply and buffered by a supercap. The supercap then provides the energy for the...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hi,
I am currently migrating from NCS 2.5.0 to 2.7.0 and running into an issue where the CMakeLists of mcuboot ( https://github.com/nrfconnect/sdk-mcuboot/blob/4c7942e58c5458ce3c4e50d3169e0f865910fe87...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
Hello,
I have a question regarding the consumption of the nRF9161 DK board when it is under the following conditions: MCU on IDLE, modem off, wake on GPIOTE input (event...
Hi,
I am hoping to send/receive binary data (a protocol) on the same UART that has logging/shell enabled. Is there a way to access the UART RX traffic that the shell gets...
Hi.
I try to build the nrf_audio sample as BIS headset with enabled FOTA and NCS2.7.0 and get the following link error for the ipc_radio image:
FAILED: zephyr/zephyr_pre0...
Hi,
Sorry to be posting a lot about my LIS2DH12 on custom hardware lately. I do believe my different inquiries are to be treated as separate.
My (modified) hardware now...