Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
SDK:11.0 Example：ble_app_hrs\pca10040\ s132_with_dfu
Hi Does nrf52810 only support a maximum of one central connection at the same time? If I currently want to connect two...
We wanted to understand better the use of external NOR Flash for nRF9161 applications. For example, in nRF9161-DK, this would be the GD25WB256E chip.
For modem delta fw...
Hi!
I just succesfully flashed my modem firmware to version 1.3.6 using the nrf programmer and a segger external programmer. I can still connect over the serial monitor...
I used nRF52840 board with SDK 17_1_0 ,
I want to used WS2812B in my project so any one can give me reference code for this or
can suggest me how can i implement its driver...
Hi,
I am using nrf52840 and SDK-16.0. Initially I was using SPI1 and SPI2. now along with this I am using SPI3.
we have added new feature which consumes 316*9*26 bytes...
I am trying to cancel a pending connection as a workaround for .
However when I run:
```
LOG_DBG ( "Peripheral connection timeout cancelling and trying later" ) ;...
Hello . I saw this issue raised previously but with no resolution so here it is again
I built the smp-svr sample in VSCode with Zephyr SDK 2.6.1 which produced a DFU package...
Hi all,
The question is about 125kbits and 500kbits long range modulation in proprietary protocol. I'v seen a post saying that is technically possible ( ).
But is...
Hello,
I have a project in progress with an NRF52840 chip. I was able to buy an aircard with the same chip www.kickstarter.com/.../aircard-find-your-wallet-always With this...
I receive the following error message when trying to install the toolchain manager (V 1.5.0) from nrf connect for desktop (V5.0.0):
Error: Failed with exit code 1. Failed...
Hi everyone, I am trying to send data over USB port for the nrf7002 dk Could anyone have any guide, tutorial, resources, or suggestion on how I should do that project config...
We have a device that does not support bonding, however the services changed and so we want to notify devices that may have cached the previous attribute table. To do this...
Hi,
Good afternoon. I try to implement littlefs file system in my external Nor Memory. I want to store a file and then want to access the file. I am using nrf52832 board...
I am new to nRF MCU's and nRF connect SDK, I want to interface my INMP441 (I2S MIC) with my nRF52840 MCU to print the mic data on serial monitor , can anyone please link me...
