Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi eveyone,
I try to using ncs DTM example , but I get error reset with following message. what is the meaning for MPSL ASSERT: 2, 80 , I cannot found any related info...
How do I get to the point that I can print a simple "Hello World" on a terminal from a custom board?
I have a custom board the is based on the nrf5340. Specifically, I am...
Hi,
we are working on a nrf52840 based device, which has an external mx25r16 flash (via SPI), having 3 partitions for: secondary-image, mcu-scatch-partition and application...
The informational section of Lesson 6 uses the "Controller/Target" nomenclature for I2C devices, but question 2 of the Quiz requires the use of "Master/Slave" nomenclature...
Hello,
I'm trying to achieve a rather simple program with three steps.
I initialize the SAADC to sample three channels (currently I only have one setup)
I "arm/prepare...
Hi,
In NRF52840, We use LFXO Oscillator (KJ3270001). We did not connect any crystal or Oscillator for HFCLK.
1) What will be the clock source for SPI and I2C communications...
Hi,
We've been working on taking the distance measurements from the nrf_dm sample and displaying them on a waveshare e-paper 2.13 in display. We've been able to get both...
Hi,
I have a project for nRF52 in VS Code. The project was able to compile and everything worked fine. However, after about a month, I reopened the project and now there...
I am developing LTE-M software on nRF9160. Previously, I checked that it runs well with nRF9160DK. Now I try it with my own board.
First, only for testing, I made following...
Hi, I'm trying to set up wireless audio stream using 2 nRF52832 Dev Kits and SGTL5000 audio boards. SDK: nRF5 SDK 17.1.0 For the wireless protocol I've used ESB, and the program...
Hi, I've been trying to modify some of the nRF5 SDK 17.1.0 BLE HID examples to make the nRF appear as a BLE HID Braille Display, that would be recognized in Android's TalkBack...
Hello,
I'm modifying the code of Wireless timer synchronization among nRF5 devices blog to use RTC instead of two TIMERs. I started with the code on Git for SDK 16. Writing...
Hello,
I am trying to interface a TCA9548A Multiplexer on my custom board. I am able to set up the channels and read the channel status' with device_get_binding successfully...
I'm just trying to get my feet under me to write some code for the nina-306 module. I'm playing along, and following the dev academy course. I can't tell if this worked or...
