Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
hi we have designed a board with nrf52840 with nrf21540.and we have designed it to communicate it with spi .Is the spi example for nrf21540 is available in sdk . if not where...
Env:
gcc version 10.3.1 20210824 (release) (GNU Arm Embedded Toolchain 10.3-2021.10)
std=c++11
nRF Connect SDK v2.0.0
Including nrf_socket.h from nrfxlib/nrf_modem...
Hi,
I am using BL653dvk, which has nRF52833 as soc. I am working on DFU-OTA example by following this link.
https://devzone.nordicsemi.com/f/nordic-q-a/83402/ncs1-8-0...
I tried to build hci_spi example application for nrf5340...
identifier "__device_dts_ord___BUS_ORD" is undefined
identifier "__device_dts_ord___P_irq_gpios_IDX_0_PH_ORD...
While migrating my project to use the new pinctrl mechanism in I ran into an issue where the I2C communication on some busses was not working. Further investigation revealed...
Nordic Connect SDK 2.0.0 moved to the use pin control interface, also for I2C.
When I tried to port some of my application I noticed a possible regression.
As a basis...
According the BLE specification, the software and firmware revision strings are mandatory. I would like to set put information about the softdevice version in the firmware...
I'm trying to make a one-shot mqtt function. The process is below
- connect - publish - disconnect
Then I coded like below. I show only the core code.
Do I have to...
Hi,
I want to get a sample that supports both BLE OTA and NUS functions, so I find the following two samples as reference and merge them together.
...\zephyr\samples\subsys...
Nordic BLE Mesh transmission is transmitted through the Publish address bound to the model in the Instance, so that subscribers can receive packets.
As shown in the figure...
Project: Variation of Nordic ble_peripheral project
SDK: 15.1, Softdevice : 132 rev 6.1
How do you change the BLE packet length? I have a project where I defined a characteristic...
I am using the example zephyr basic button which gives output when the button is pressed.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/zephyr/samples/basic...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
we currently have a product which use nrf52832 as processor using SD132 for BLE capability with DFU capability
we want to build a sister product with nrf552810 with no SD...
HI,
We are looking to multiplex a few I/O on the NRF52840 to save pin count on a header. If D+ or D- get driven when VBUS is unpowered, will that damage the NRF52840? Or...
