Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hello,
I am trying to run the wifi_scan example but I am getting a BUS FAULT error as seen below. The SDK is v3.1.0, and the SDK Toolchain is also v3.1.0.
1. Going...
i have version 0.9.2 of the nRF54L DK....
i've noticed there is now 1.0.0 documentation....
have there been any HW changes -- use of "production" MCUs, etc....
more...
Hi Team,
We are looking into the new Thingy 91 X and were wondering if it will be able to run the nRF91 Pizza Demo .
I understand the demo was originally created for the...
Hello,
I'm working on Windows 11, with the nRF Connect for VS Code v2025.5.512 extension, with ncs v3.0.2. I'm using the nRF54L15-dk (PCA10156; 0.9.2; 2025.7) development...
citing the following issues
I've been able to implement the 16 Mhz on the SPIM3. However, the incoming data on the MISO is still corrupted. With my oscilloscope I can...
Currently, we are developing our own board with NRF5340-CLAA. It does not have a 32.768kHz crystal oscillator, only an external 32MHz crystal oscillator. We have applied the...
Hi,
We have a working firmware that uses LTE-M for network connectivity to connect to NRF Cloud. But upon testing with NB-IoT configuration (CONFIG_LTE_NETWORK_MODE_NBIOT_GPS...
Hello, the time to ask for help has come again... I keep hitting a crash in my BM833 code related to "Illegal use of the EPSR". Code is fairly simple and supposed to be pretty...
Hi,
hi have the same problem related here: https://devzone.nordicsemi.com/f/nordic-q-a/91890/nrf52-reports-two-jlink-cdc-uart-ports
With revision 2, UART show only one...
We are looking into a device using the NRF54L to do low power indoor tracking since it has a very low power consumption when using the RADIO peripheral.
We see that the...
Hello,
I am facing an issue with nRF Cloud device provisioning. I am using the nrfcloud-util tool to provision the device to nRF Cloud (as recommended for production provisioning...
Hi all,
I’m running into issues flashing an Arduino Nano 33 BLE Rev2 (nRF52840) using Zephyr and the bossac runner. I consistently hit a “Flash erase failed” error and can...
Dear Nordic,
We’ve developed an application which runs on an nRF9151 DK using NCS 2.8.2. The device is running modem fw nrf91x1_2.0.2. Our application has enabled modem...
