I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Hello, I'm trying to update services list on central device after adding a new service. However, sd_ble_gatts_service_changed returns NRF_ERROR_NOT_SUPPORTED . After looking...
Hello,
In my application, I need to activate BLE during startup only if some conditions are met otherwise I put the nRF52 in SystemOff mode. BLE should not be activated...
Hi,
I have been receiving the error: undeclared identifier "TWI0_USE_EASY_DMA". I researched and found that the solution was to include "nrf_drv_config.h" and add #define...
Hi, I have problem with discover services in advertising mode on NRF51822-BEACON. There is default firmware in this beacon. I using Xamarin on Visual Studio 2015. It is connected...
I have integrated IAR code into my company system.
with the Jlink_monitor.c, jlink_monitor.h , jlink_monitor_ISR_ISR.s and enableMonitorMode.mac.
Step 1: I loaded code...
Hi,
I am trying to use the nrf_drv_twi class but I cannot define a nrf_drv_twi_t instance. When I write the code
`nrf_drv_twi_t twi = NRF_DRV_TWI_INSTANCE(0);
I get...
Hi,
It is indicated on page 59 of the datasheet (rev1.0), concerning the register nr.8 OBSERVE_TX, that "the counter PLOS_CNT is reset by writing to RF_CH . See page 75...
I am working with SDK12.2.0. I see that transports seem to be registered as section variables with the identifier dfu_trans
I have added a section definition in flash to...
Not sure if this is a typo in the function comments or a small bug, but thought you'd probably want to address it either way. I'm on the most recent NRF5-SDK (12.2.0) and...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Gentlemen,
I'm trying to develop a Health profile solution that works with Win 8.1
I'm using SDK 6.0 and S110 v 7
Win 8.1
I found the Win 8.1 sample app...
I am looking at the Master Emulator examples ProximityDemo and HealthThermoDemo. I can use both to connect to one device that I have (Device A). I try to use ProximityDemo...
Hi,
I want to achieve DFU OTA nRF51 using NRF52832.Is it any example,or data transfer message sequence charts documentation? Could you give me some suggestions?
Thanks...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi,
I hope you are doing well. I am working on nrf51822 project. I want the nrf51822 to advertise for 5 secs and then sleep for say 30 mins or an hour and then wake up...
