Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi there,
This almost certainly has a simple answer but I can't work it out. I'm using the sample WIFI Scan for the above boards and can successfully scan away. But I'd...
Hi there, I am new to working with UART. I have managed to load the Nordic UART Service Client(Central) and UART Serial Port Emulation(Peripheral) without any sensors attached...
So, I am working on nrf52840 with nrf connect sdk and I want to get date and time in my project, I found a library in nrf connect sdk ->libraries->other libraries->date-time...
NCS 2.7.0 Zephyr 3.6.99
I have &uart1 described with status = "okay"
With a sub node of gnssdev: gnss-nmea-generic also with status = "okay"
I have tried with both pointing...
Hi, In one of the previous ticket (link: ), there is a link about an example to create an application with USB CDC/ACM and MSC at the same time. The link is no longer valid...
I am writing software for a battery-powered device that needs to go into the lowest power possible sleep mode when not in use and be able to wake up with one of 8 buttons...
Hello,
I've been trying to get the nRF Desktop Dongle/HID Forwarder to work, ie. I program a nrf52840DK as a HID forwarder, it connects to my bluetooth keyboard, and then...
Hey Team,
While connecting the battery to the nRF5340 Audio DK, we have observed that it only charges the batteries with 3 pin connector is being charged. However when we...
Hi, I just want to read accel and gyro data from the on-board BMI270 IMU on the Thingy 53. I'm using the sample code from zephyr and I've modified the dts and overlay file...
my chip is nrf52833. In guide document , the XC1 and XC2 would connect to capacity. Both pin is used.
My project need one pin TCXO. which pin I should connect to? XC1 or...
Hi, everyone.
I am testing reading/writing data between n52840 and n9160 through UART with buf_len=1(byte by byte) based on Zephyr's UART_ASYNC_API provided in ncs v2.6...
I have an application that tries to configure pin 9 of port 0 on the nrf52840. this pin is reserved for NFC use. in one application it was enough to add:
& uicr {
nfct...
Hi ,
In NCS 2.8.0 the ESB-PTX sample how to config to achieve?
Now I had disable the UART log,after transmit 20 seconds I want to config the nRF54L15 into a low power...
There are 2 software: 1.0.1 and 1.0.2. When I load the 1.0.1 hex with bootloader with the programmer, it draws 9uA current. But when I update it to 1.0.2 with DFU, the current...
