Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
in devacademy there are mqtt and gnss sample. when I put the mqtt configs to gnss sample. give an error. I did not add main code yet. just only put configs and cmake.
after...
I came across a client example that use the
I read about BT_GATT_SUBSCRIBE_FLAG_VOLATILE
How I know if the subscription is not saved on the GATT server side (which...
Hi,
Is there any existing support for an e-ink display interfacing with the nRF52840? Something that already has an existing LVGL driver and can be integrated with an nRF...
Hi team,
I'm currently facing an issue with the nRF52832 and nRF52833 gateways in our setup. Here are the details:
Current Configuration: - Scan Interval: 100ms - Scan...
Hello everyone,
I have developed a program that utilizes UART communication, Bluetooth Mesh, and TWI/I²C functionalities, all within the framework of the Zephyr project...
HI,
I am building an IoT product using NRF58233 ICs. In which I use 3 PWM channels and 3 ADC channels. You can review the principle I attached to make sure nothing went...
Hi,
I have a strange problem. I use a serial port timer to retrieve serial port data. When I compile with debug, the program runs normally, but when I compile with release...
Hi,
I am using nRF52840 DK and Bluetooth Observer example program. I am implementing filtering. I am having trouble add include scan.h which is located at C:\ncs\v2.4.2...
Hi Support Team,
I have an nRF7002 DK board and I am using SDK v2.6.0. I am facing an issue when sending data from the client to the server. Below are the steps taken: 1...
Dear colleagues,
with the newer SDK (I am now using NCS v2.5.0 and 2.6.0), I have difficulties finding the right SYSTEM OFF mode current. Code currently looks like as follows...
Hi
I use nRF7002 with SDK v2.52, try to connect external MCU and use uart call back function, to recieved and send bcak the recieved data, It will happen fatal error and...
Hi,
I have bunch of SEDs (sensors/clients) and one or more FTDs (hosts) working on CoAP protocol. SEDs send data packets once in a while and mostly sleeping. I have few...
Hi,
I'm testing the NCS direction-finding-connectionless demo,
NCS V2.6.0
this is my overlay:
and my ant_patterns:
According to the white paper and some other...
Please, I want to flash Zigbee Weather station App on thingy53, I faced two problems:
1- i can't find the board in build configuration.
2- i tried to use programmer and...
Team Nordic,
Question for you. In nRF5340 datasheet, page 1, Flash and RAM description : https://infocenter.nordicsemi.com/pdf/nRF5340_PS_v1.3.pdf
I found description...
