I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
I'm using a custom board based upon the nRF52840. The BME680 chip works fine in another RTOS but the zephyr/nRF connect example is throwing errors.
I added a fair amount...
hi
We are conducting SIG certification testing with nRF52832 and DFM.
(CMW270)
The TX test was completed normally.
However, a problem occurred in the RX test.
...
Good morning,
Today for a Brazilian Logistic company, I am developing a Embedded System for Low-power tracking and other features, with a nRF52840 in a RAKWireless solution...
i have developed the VL53L5CX code with BLE nrf52840 and it is working fine but issue i have faced is the USB port Restarted Whenever Firmware Download Process Start below...
HI Nordic support team.
I have a question relate to TX power in ANT application:
- ANT Tx application using: ant_broadcast ->Tx
- ANT Rx application using: ant_continuous_scanning_controller...
I've been running a Central + Peripheral application. I can successfully scan for devices and get the advertising data.
However, when I try to connect, the code seems to...
I am running the Direction Finding Connectionless Beacon sample using my nRF52833DK to transmit CTE packets. I am using the u-Blox ANT-B10 antenna board to receive the CTE...
"I am using ncs v2.6.1 on VSCODE, and the following issues have occurred:
Issues:
- Existing build files are not visible in the application.
- New builds are possible...
The multicell loaction has been working fine for a long time. About 8 days ago, I started to receive an error when requesting the location through "Here"
Any help would...
I am working on an application for an LE Audio Broadcast sink on an nrf5340 Audio DK. I am using code from the nrf5340 Audio application (v2.6.0) for the le audio parts. I...
Hi! I'm new to using the Nordic products and I wanted to be able to power my Thingy 91 device without the use if the USB and with a separate external power supply. On the...
Hi there,
Currently we are developing our own system to drive WS2812B LED's using the NRFX pwm library. And the coloring and signaling works fine when it is in a bare metal...
Hi,
I am using nrf52840 and SDK17.1.0.
I need to calculate CRC16 for communication with an another module. I found that we have an API for that. I would like to know what...
We are planning to develop an Matter door lock which includes NFC/RFID, Audio, keypad and BLE functionalities used separately. I am considering using either the nRF52840 or...
I tried setting the VDD voltage in the 9161 DK to 3,3 V, but it remains at ~1,76 V.
I'm able to enable/disable the GPIO extender just fine, so at least reading & writing...
