Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Hello I'm working on a nRF9151 DK using nRF Connect plugin for VC.
I was able to program and run my without any problem... but then suddenly the flash process stopped to...
Hello.
I use the bare metal SDK and I would like to generate a GRTC interrupt every 250ms to wakeup my system.
Which resources does the zephyr is already using (GRTC_x_IRQn...
Hi,
I’m using an nRF52810 with nRF Connect SDK v2.5.1. I want to read the internal temperature sensor. I started from the LBS sample and added NSMS to report the temperature...
I'm working on the firmware for a custom board built around the nRF9151 SiP. The firmware is built against the nrf9151dk/nrf9151/ns board target included in zephyr, with an...
HI
I am using nRF54L15 PDK with NCS 3.0.0. In my code, I am using NVS to store data on the MX25R64 flash on the PDK. The initialization code is as follows:
struct flash_pages_info...
Hello, I am currently working on a PDM microphone project using nRF52840 and Zephyr RTOS. I've been testing the official Zephyr sample (located at dmicncs/v2.9.0/zephyr/samples...
I have three questions regarding the electrical parameters of the NRF9151 chip:
For a GPIO configured as output: What is the maximum source current per pin when driving...
Hi,Team,
I am developing the nrf54l15-dk, and the version of my NCS is v3.0.2. Because our terminal device 1 does not support using ble-FOTA, I used another terminal device...
Hi,
We have a custom nRF9160 board with chip antennas for LTE and GNSS. They are Ignion antennas with matching circuits customised to our board dimensions. We also use...
Hello, We are developing an application with nRF52810 based on nRF Connect SDK V2.4.1. The application is utilizing the BLE connection, particularly the NUS Service (emulation...
Hi,
I’m testing low-power behavior on an nRF52811 device.
When SoftDevice is not enabled , calling nrf_pwr_mgmt_run() gives me a stable ~5 µA average with no visible...
I am experimenting with ble_app_uart & ble_app_uart_c using two terminal windows, and I am sending a string of 1000 chars from the central to the device.
Although they are...
Hi Nordic
As information of nrf connect SDK, NCS3.0.0 ble_coex sample at NRF7002 DK can share single antenna for BLE and WIFI protocols.
It only needs to set "CONFIG_COEX_SEP_ANTENNAS...
I’m trying to use the Zephyr software split BLE controller ( BT_LL_SW_SPLIT ) on the nRF54L15 DK with NCS 3.0.1. I understand that this controller is not certified, but I...
