We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I have built a system with 2 MCUs communicating through I2C. The NRF52 is I2C slave and the other MCU is master. I have implemented a command style interface which sends commands...
Hi
We have a strange problem with the Kconfig of the azure_iot:hzb sample project from the v.2.1.1 SDK:
We have configured f.e. the "Azure Iot Hub hostname" and the "Device...
Hello!
I have a custom board that I am trying to set up but I'm not entirely sure what to do.
In my board, I have an nRF5340 SoC, that has 2 interfaced with the external...
Hi Nordic team
I found a sample for ADC (saadc) on the nRF5340 at the end of this post . The answer is related to the nRF5340 PDK.
Is there a way to use this code on a...
Dear Team,
We would like to add nfc feature to our product. We are bit concerned about the nfc antenna size that comes with nrf52 dk.
What is the smallest antenna size...
Hi,
I am trying to install nRF Connect SDK using Toolchain Manager in nRF Connect for Desktop. I seem to consistently fail with this error for the latest version v2.1.1...
Greetings,
We are currently evaluating the nRF Connect SDK in comparison to the nRF5 SDK for our new product (BLE enabled & battery powered) for which low power consumption...
I'm having trouble activating a PDN on a running/connected device. Here's the code:
Seems like I'm missing something here. pdn_init does get called on system setup...
Hi,
Just wondered about the following ....
Strange parts of this code ... Or things I don't understand
After the first READ in Setup() it successfully reads the data...
I am trying to implement a simple uart echo test using nRF21540 DB board, but I always get NRFX_ERROR_FORBIDDEN when trying to transmit.
This is the initialization code...
I am using nRF5 SDK v16.0.0 on nRF52832. IDE is SES. I am also using FreeRTOS
What order should the following methods be called in? Does it matter when fds_app_init is called...
Hi Team,
I am using SEGGER 5.4 IDE and NRF52840DK controller.
I did not understand the difference between Terminal Emulator and Debug Terminal in Segger IDE.
I am not...
Hi,
I want to configure Timer1 (32 bit ) to run up to 1 sec and then reset. I want this to be done continuously with the help of Short but without using the event handler...
Hello, I have an nRF52811 on a custom board and have been having some issues. I have a nRF52840DK which I used to flash the custom board (while powering the board with the...
I connected it to an external mcu as shown below. After downloading serial lte modem to nrf9160,
at command is sent, but it does not respond. Connect only 3 pins for communication...
