I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
I've had a lot of success with the nRF51 series but recently came to the conclusion that it isn't suitable for our needs and trying to transition to the nRF52.
I picked...
Hello everyone,
I'm developing my own board using the nRF5340. I am quite lost because of the capacitance matching that I need to perform with the 32M Crystal and the 32k...
Dear all.
I have the nRF52840dk and nrf52833dk kits.
I am having the same problem with this guy. And now my kits lost their Jlink and Com port.
In the answer, I found...
I developed a product on ncs1.9.0. It needs to connect to the nb network and support the gps positioning function. When the device is running, I found a problem that when...
The Zephyr documentation about ADC ( https://docs.zephyrproject.org/latest/hardware/peripherals/adc.html ) mentioned ADC _CHANNEL_CFG_DT usage in device tree and later source...
Hi,
I would like to enable the SAADC to read multiple DPPI channels. I am using a timer to publish multiple channels and my code looks like this:
However, the...
Dear all
I am developing a BLE product, and would like to have a different device name for each unit like Product1, Product2 etc. when advertising, so user can identify...
Hi! We are updating our application from NCS 1.9 to NCS 2.1. In the documentation of the HTTP AT command of the 2.X versions of NCS the XHTTPCRSP notification is documented...
Hi Nordic,
1. I am planning to do DFU update with UART
2. I Build smp_svr and flashed successfully when am using mcumgr its getting NMP Timeout
3. I added CONFIG_MCUMGR_SMP_UART...
Hello,
In my project, I have a device (nrf52833 custom board) which I want to operate in dual role (central/peripheral). I've followed a ble_app_hrs_rscs_relay example...
Dear Sir/Madam,
We developeted a smart device based on nRF52840 chipset(to be more accuracy, we desgined our own module based on this chipset, then our end product use the...
I'm currently trying to change the host name of "https_client" and check the operation, but it doesn't work.
Even after changing the host name back to the original, "Waiting...
Hi,
We want to do provisioning of multiple mesh nodes using pb-adv procedure. we installed nrf MESH app, but we are not able to do provisioning for one node using Pb-adv...
Hello everybody. I'm designing a custom PCB fed by a typical 3.7 V nominal 4.2 V peak lipo battery, where minimal area and thus component count is a key factor. Aside from...
