Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
I want to use nRF5340's GPIOTE and DPPI implementation, pull up PA_SWITCH_CTX_PIN when NRF_RADIO->EVENTS_RXREADY is triggered, and pull down PA_SWITCH_CTX_PIN when NRF_RADIO...
Hi guys,
I have an interesting idea - organize a network for realtime audio communication. Basically duplex Walkie-Talkie but using bluetooth headsets. I tried to use ESP32...
Hello everyone,
at the moment I am working on a BLE program which collects data from various sensors and passes it to a Central device. For the transmission the BLE NUS...
I am using ESB with dynamic payload lengths. When I use length 252, I am sending the alphabet repeating, and I can see that the data cuts off around position 30 and repeats...
Are there any known issues when using a nRF52840 and S140 6.0.0 soft device and trying to transmit at +8 dB? From our measurements is appears that +4dB does indeed increase...
Hello,
I am using the nRF 9160 DK board. I am trying to create simple thread in Zephyr.
but the thread it's not running.
this is the code:
I tried also the other...
I accidentally pressed "verified" on https://devzone.nordicsemi.com/f/nordic-q-a/91104/making-rand-work-on-nrf52-nrf53-with-nrf-connect-sdk when it wasn't and I don't seem...
I am testing my own mesh protocol based on 802.15.4 using the NRF52840 dongle.
The reported RSSI value from nrf_radio_rssi_sample_get() never goes below -89dbm.
On the...
Hi,
I'm using a nrf52832 and NCS 1.9.0 and I would like to be able to use SMP to make firmware updates using BLE. I'm was able to perform FOTA, but the flash is divided...
Greetings!
We are trying to troubleshoot occasional hangup issue. We run the app in debug mode. When it hangs up, we hit pause and got the followings in the Call Stack window...
Hi,
I want to use nrf5340 dk board to debug nrf52840dongle, i have connected two board with a cable and have checked the signal is good( nrf5340 debug out p19 ------ nrf52840...
Hello all
the BLE module with the nRF52820 is programmed with a ble_app_uart_pca100e example from the nRF5SDK ver 17.1.0, according to the RSSI graph it seems it works ...
Hello Reader, I noticed two almost similar modules " DK buttons and LEDs" library and the "CAF LED & Button" library (or module). What is the difference between DK buttons...
I get the following error message from my device
àÓ FATAL: Exception occurred in Secure State [10.2 10:01:52.062]FATAL: ***** HARD FAULT ***** [10.2 10:01:52.062]FATAL:...
We have both native iOS and Android-apps that handle DFU-updates of our BLE-FW on our HW-devices. We are currently experiencing a dip in success rate (according to our firebase...
