Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi Team,
I'm installing nRF connect SDK in my PC and i'm using ubuntu for Zephyr RTOS.
When i'm run this command that time error is coming "west init - m https : // github...
I need to use can bus for my application. The chip that will be used will be the MCP2515 can bus ic. For testing puposes i went and tried the CAN sample which is meant for...
I had look on overlay-low-power-conf file and in folder child_image on spm.conf file that UART_SERIAL=n is set. I need to interface a UART device to nRF9160.
1. Is asset_tracker_v2...
I installed the nRF Toolbox on my phone and received data through BLE uart. However, how can I download/save this data on my phone? For example, I send the temperature to...
Hi,
I'm trying to send an data array over ble nus.
This didn't work.
I'm also getting this warning.
I'm doing something wrong, but I don't know what. Do I also...
Hello,
I am making a Firmware for the FCC certification, I must emit at 3 different frequency, 2404MHz (ch37), 2440MHz (ch17) and 2480MHz (ch39) on a nrf52832.
I unfortunately...
Hello,
I have installed the NCS toolchain using the Toolchain Manager app. I am using toolchain version 2.0.0. Here is the error I get when running `west status` :
Same...
I received Thingy:53 and tested it by following the Getting started with Thingy:53 SDK documentation.
The problem arises from the sentence below.
Getting started with...
Hello,
I'm using the LTE Link Monitor v2.0.1 with the nrf9160dk_serial_lte_modem_2022-06-02_880c82db application on a nRF9160.
I'm able to establish the connexion and...
I saw a news report on Nordic's official website that Nordic's NB products have passed the certification of Chinatelecom. I wonder if they have passed the certification of...
Is there a way to add an offset to the nRF5340's reported RSSI to compensate for any front end loss or gain the design might have? This is to get to an RSSI value at the antenna...
Hi,
I'm using HID mouse example in SDK17.02.
After downloaded soft device and the application, I add the device in my pc blue tooth. I can see the battery level normally...
Hi,
I'm looking for a product Bluetooth 5.2 Radio System-on-Chip (SoC) which is of automotive type, and their operating temperature ranges are (-40 to +125)
I'm working on Electronic Shelf Label project using Feather nRF52 with Raspberry pi for server connection. I need to Adafruit Feather nRF52 to receive data from raspberry...
Hi Sir,
We follow this link to test the NIDD, but I'm not sure whether it is successful.
1. Can we know the NIDD link successful or not from the log? What can we see if...
