Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hello,
I am currently developing using Zephyr/NCS an application that supports FOTA/DFU.
The device needs to be tapped to be woken up and start advertising. So, when...
Hi, I want to build a Bluetooth LE peripheral application with nRF5340. The channel must be able to sustain an output stream of 8 kbit/s.
Other desirable features are: ...
GPS sample stops updating timestamp after a few days of uptime indoors
Tested devices: Thingy:91, nRF9160dk Tested firmwares: mfw_nrf9160_1.2.1, mfw_nrf9160_1.2.2
Demo...
I have a nRF52820-DK evaluation board which I am trying to develop on. I followed the manual install procedure on to my xubuntu Linux desktop. I followed these instructions...
Hi ! I have configured Zero bit length of S1 in radio packet ( nrf52840 ) but it is still mapped to the RAM.
... ((NRF_S1LEN_BITS << RADIO_PCNF0_S1LEN_Pos) & (RADIO_PCNF0_S1LEN_Msk...
We would like to use Zigbeee on the nRF52820, however, it seems from other threads that neither the "nRF5 SDK for Thread and Zigbee" nor the "nRF Connect SDK" support it,...
Hello sir,
I am using nrf52832 soc with customized board having gpio pin with P0.2,P0.3 and P0.4 used for led blinking for different purposes.The function used for led blinking...
Hello,
I have a problem with the SPI of the nRF52DK 52832, and Zephyr 1.6.1. I have to transmit 10 frames of 5760 bytes each to the TFT display with the ST7789 driver. ...
I am just creating this issue as a bug report. (my github issue: https://github.com/zephyrproject-rtos/zephyr/issues/38688 )
There is currently a bug in zephyrs handling...
Hi!
I had some time with the Thingy:91 and was able to get my own application running on the device using the nRF Connect Programmer application. To eliminate the need for...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I want to read / write a value to the specified address of the flash. According to...
Hello.
I'm trying to get data from a pressure sensor.
But it seems that BLE device is not properly got data from the sensor.
Here is a data sheet of the sensor. (Please...
Hello everyone, I am using NrfConnect with Zephyr on Segger embedded studio . I want tu use the math logarithm function in my code and print the result on the debug terminal...
Hello,
We have a wearable-type device with custom BLE services and characteristics. We would like to log all data from our services on a PC. Would you happen to know of...
