I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello,
I am working on project where my requirement is something like... Device will advertise and it gets scanned by its own scanning.
What I have done so far......
Hello.
We are migrating from SEGGER Embedded Studio (SES) to IAR Embedded Workbench (IAR). At that time, an error occurs that "__ICFEDIT_region_RAM_start__" is not defined...
I want to select the nRF52 series SoC as our product platform. I have a use case in which I want to get the optimal channel map and I find the "sd_ble_opt_get()" function...
I have taken over a older (5+ years) project that uses Gazell, but it didn't use the Gazell link layer to do wireless pairing. We were looking at shifting to SDK 12.3 (last...
Hi,
I am using the CAF BLE components to use bluetooth on the nRF52840, which I control over HCI via the nRF9160. This is all working.
To use the CAF advertising component...
Hello Nordic DevZone, My name is Ted, and I'm having some difficulty with a recently installed Nordic / Zephyr SDK and toolchain. On 2021-07-24 I downloaded and installed...
I'm trying to read the memory off of a BT840F, which I'm hoping to do via a debugger. I've read that a tag-connect cable can be used to connect from a pcb to the debug out...
Hi,
I tried running the "chat" example on two NRF52833DK boards, one as a sender sending a "Hello World" message every 500 milliseconds, the other as a receiver, and found...
Hi,
I have an issue when I migrate my app from nrf52 sdk v16 to v17.
I have setup an app with an uart communication, an app timer and a watchdog. All off these (uart and...
We are using the Libuarte - advanced UARTE driver and sometimes see crashes in the uart_evt_handler code in nrf_libuarte_async.c when it gets a NRF_LIBUARTE_DRV_EVT_RX_DATA...
I am interested in developing a Cloud Driver that communicates to my own servers over HTTPS.
Cloud API documentations state that a driver needs to implement a set number...
Can I UART/SPI/I2C on any pin of NRF52832?
- Can I UART/SPI/I2C on any pin of NRF52832 which is mentioned general-purpose I/O pin ?
- Is there any limit on how...
Hi,
Actually we are searching for a chip which has more than one UART channel for communication.
Can we define more than one UART channel with GPIO configuration? Is it...
Hello, I am currently using the TWI in non-blocking mode, however I frequently run into the issue where the code gets stuck on nrf_drv_twi_tx. function at the return result...
