Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
I followed the steps below to set up my development environment, based on the instructions from link
Setup 1 1. Installed SEGGER J-Link v8.56a Path: C:\Program Files\SEGGER...
We have this custom sensor board, running nRF9160.
Application code built with SDK 2.5.0, running modem FW 1.3.2, and using LTE-M connecting to MS Azure IoTHub with MQTT...
Hello, I have an application, that uses the Bluetooth to do over the air updates using these two configs:
CONFIG_BOOTLOADER_MCUBOOT =y
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
Hi all
I’m having a horrible time trying to get an nRF7002EB Wi-Fi coprocessor working with a nRF52840 via QSPI interface in nRF Connect SDK 3.0.2 (Zephyr 4.0.99). I'm using...
Hello,
We are working with Onomondo in integrating their software SIM. We have it working and sending and receiving data, but am having some issues figuring out what is...
Issue Summary: When running west flash to program my board using the UF2 runner, the process fails with an OSError related to copying the .uf2 file to the UF2 bootloader drive...
Hello!
I can use the offloaded sockets driver with these configuration options on the native_sim target:
CONFIG_NET_DRIVERS=y CONFIG_NET_NATIVE_OFFLOADED_SOCKETS=y
However...
Problem:
I am working on USB, CDC ACM, USB Mass Storage (using SD Card). I currently want to be able to still use the USB stack functions with only my USB Mass Storage being...
I'm experiencing an issue with my Power Profiler Kit II (PPK2) when using nRF Connect for Desktop .
System configuration:
nRF Connect for Desktop version: 5.2.0
...
I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Hello Nordic team,
I would like to check if you provide a template for RED-DA EN18031 for nrf52840 which we can use to modify and fill based on what we have implemented...
I use nRF5340 audio DK,iso_time_sync example, can successfully send BIS data, then I use DK as controller, bumble( google.github.io/.../index.html) as host and it fails to...
Hi, I am currently integrating nRF52832 with TLV320AIC3104 codec. I have successfully initialized I2C and I2S communication between the two boards and configured nRF52832...
Hello,
I am evaluating the nRF54L15 for potential use in a new product. I did some measurements of the average current consumption and the vaues were a bit higher than i...
