I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
To the kind attention of Nordic support team,
we are experiencing a very random and rare loosing of existing ble bonding infos (device side). So that to reconnect to the...
We are getting a "No SOURCES given to target: drivers__ipm" error making build fail for our custom board when trying to move to 1.5.0 for official nRF53 production support...
Hi,
I am using NRF52832 with SDK 15.0, SDK Mesh 4.0.
As my knowledge, the OTA speed of Mesh DFU is very slow.
So can I use SDK DFU for faster speed?
Thank you.
Hi
Followed all the getting started instructions given here
https://nordicsemiconductor.github.io/asset-tracker-cloud-docs/v1.5.x/docs/aws/GettingStarted.html
and...
Setup :
Device: nRF52840DK PCA10056
Software: NCS v1.3.99
What I am trying to do:
I have 3 SAADC sequences that I need to run for my application that I wish to poll...
HI,
I'm using the zigbee CLI example as coordinator and have another CLI device for reference as router. With my sniffer I can log the association sequence with the cli...
Hello,
I have a nrf5340 PDK .
The kit does not work right, because i got a several errors.
For example in nrf connect v.3.6.1 the PDK is shown as 000000123456 also in...
Hello Nordic support,
I would like to confirm whether nrf52840 supports only Bluetooth 5.0 features or does it also support Bluetooth 5.2 features. If it supports Bluetooth...
Hello, I am working on Nrf52 mesh network and need to update device via any host mcu or flash connected with the nrf52. But could not find any way to implement it.
If anyone...
I have changed our code that has been running on v1.4 successfully to v1.5
Mainly because I'm hoping for an improvement in the reliability of the new modem library.
However...
Hi All
Can anyone please point me to any documentation/app note that explains how the UE receives a Valid paging message when Network wants to reach the UE. Is there a...
Hallo,
IDE: Segger Embedded Studio
nrf52840 DK
Custom Board with ProteusIII
I have designed a custom board with ProteusIII (nrf52840 SoC) and was working with...
Hi,
I am currently in India city Bengaluru.
as ibasis sim does not support my region so
i am trying to connect nrf9160 to lte network using airtel sim card, but it is...
Hi,
We are working on a new product with " nRF52832 " IC. We want to test our design RF antenna (PCB trace Antenna) performance. For RF test we found an example code and...
If I change the NRF_SDH_BLE_GATT_MAX_MTU_SIZE in sdk_config.h to any value greater than 23, immediately after connecting the stack executes a sd_ble_gattc_exchange_mtu_request...
