I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi
I'm developing with nRF52832.
I am using Segger Enbed Studio as a development tool.
When you download a program from Segger, Segger does reset once, and I wonder...
Hi,
I want to run QSPI application example on my nRF52840DK (PCA10056) board with logs seen via UART. I successfully uploaded QSPI bootloader example and Blinky SysTick...
Hello,
I'm developing an BLE application with NCS where I want to be able to change the BLE device name during runtime. Therefore I enabled CONFIG_BT_DEVICE_NAME_DYNAMIC...
Now we development a switch and use it control the light. When i push switch close the light, there was still a faint light. Then i found when NVIC_SetPendingIRQ(EVENT_IRQn...
What I intended was to write x'700' to x'10001080' i.e. NRF_UICR->CUSTOMER[0] !
When ran my application, which outputs NRF_UICR->CUSTOMER[0] to the log, I was very confused...
In firmware I can read the programmed UICR serial number as follows: -
uint32_t serial;
memcpy(&serial, (uint32_t*)0x10001080, 4);
Is it possible to program the UICR...
The peripheral_lbs sample on the nRF5340 with the nRFConnect v1.5.0 builds fine and the merged.hex file downloads fine, but it does not appear to be running, no blinking light...
I have a program that recieves data from another chip over Serial. It sends 2048 blocks of data which than get transmitted to our C2 over mqtt. Problem is that afther 12/14...
Hi,
I am trying to receive and send data from an android device to an nrf52840 device with USB CDC. I have already installed the application using this link https://jimmywongiot...
Hi!
If I build my project with TF-M I noticed that at least the flash usage report differs dramatically compared to the original firmware:
Original:
Memory region |...
Hello
I am currently porting nRF52833 using SPI communication with other MCU (AD5940).
AD5940 provides an example of porting with stm32, which we are referring to.
Currently...
The document nRF52811_PS_v1.0 states that the Threshold Voltage Tolerance of the Power Fail comparator is typically +/- 1% and max. +/-5%.
Under which circumstances does...
Please tell me the UICR setting in nRF52810 and S112. Currently, when I develop with nRF52810 and S112, the area of UICR is 0xFF. [1]The oscillator is equipped with 32MHz...
