Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
I need to get quite a lot of logs and quite fast too. How do I do I get the logs into a file?
I tried with Segger RTT logger, but it tends to give up quite quickly. I heard...
I want my system to sleep for some time, but its waking up and I am unable to understand which interrupt occurred. I want to know which interrupt caused the system to wake...
Hi All,
I want to implement a function to send data from the internet coap client to nrf52840 DK coap server. The nrf52840 runs .hex file which is one modified from Nordic...
Hello, I'm testing an example of a zigby light bulb with a nrf52840 (pca 10056) board.
Here, when I press "BUTNERT 1" on ZED, I want to send the [ON/OFF] status of the current...
The average current during the nRF9160 test DRX is 2.2mA. The period of DRX is 2.56s. Using a China Mobile IoT card. I am testing on the DK board and have turned off all peripherals...
I used NRF24L01 to transmit the data without ACK mode. The receiver received the data normally when only the WR_TX_PLOAD_NACK instruction was used to send the data.If the...
Hello,
I want to set a GPIO Pin to high. Therefore I wrote the code below.
But when the software is written onto the nrf52811, I can not messure any voltage.
I do not...
Hi,
I am going to do data communication between two boards with libuarte. I see that both txdata and rxdata should be uint8_t*. But if I try to transmit the char*, will...
Hi On a nrf9160, I need to send data via UART(E) at 921600 baud. According to the UARTE BAUDRATE register documentation the register value 0xF000000 (Baud921600) leads to...
Hi,
I changed application main.c to enter in to DFU mode after 20 seconds. System is reset every 20 seconds and the boot messages are printed. The message "Booting (0x8200...
I am trying to measure distance with a vl53l1x sensor through the twi_sensor example. I uploaded the code to segger by referring to sparkfun, but twi_handler does not work...
Hi
using sdk17, softdevice132...
There are some parts of the central implementation that I don't understand.
It is based on cle_uart_app_c.
Isn't the function bl_nus_chars_received_outprint_print_called...
It is amazing how common this error is - there must be 100 posts. Yet none solve the problem and none explain it. It suggests that there is some serious work needed to improve...
I've been developing using nRF52840 using the nRF5 SDK. I have also been using FreeRTOS in my projects.
I recently received an nRF5340pdk to evaluate the nRF5340. I have...
