I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello mates, Im trying to run this proyect:
nrf52-spi-i2c-master-ssd1306 ( github.com/.../nrf52-spi-i2c-master-ssd1306 )
I have the display and that kit development...
Currently I want to build the light_switch examples from the nrf5_SDK_for_Mesh_v2.2.0 on my nrf52832 dev board but this gives the following error "boards.h: No such file or...
I would like to know if Nordic has implemented software support for CryptoCell-312 (nRF5340) in the latest master branch?
Right now I am able to use mbedTLS "frontend",...
Hello All
Please tell me about nRF Connect (iOS).
When the module and nRF Connect (Ver 2.0.1) are connected using LESC, they will be disconnected after bonding is completed...
I am using the ble_app_uart example and I am having a hard time finding the function that writes a UART message to BLE from the Nordic to the host. uart_event_handle() seems...
Hello All,
I am working on nRF51822 use SDK nRF5 12.3.0 version in IAR workbench.
I am write data in the flash so for that i follow below steps,
Step 1: press button...
So, I need to send and receive a data frame with 39 Bytes with a system Dongle-Arduino(with a nRF24L01 module).
My problem is, I tried to configure Dongle to communicate...
Hi,
I cannot update the firmware on the nrf9160 MLM1 Preview development kit we have. Is this possible? or is the devkit voided for the latest nrf connect and nrfjprog...
Good afternoon everyone,
I'm trying to make a working application for the BLE NUS example but with the support of FreeRTOS that is MANDATORY. I work with KEIL. I started...
with NCS v1.3.0 is there a way to turn off partition manager? I want to be able to build my app and mcuboot separately and not use partition manager at all.
Is it possibe to upgrade nRF52-DK on board programmer to program nRF52840? I already have this nRF52DK but in final I found that 52840 will be better choise for my proyect...
Hi, I am reading the datasheet of both the sensor. but i2c register are different.
I am currently work on vl53l1x. please give me the response as early as possible. thanks...
Using SDK 16.0.0 on an nRF 52840 board.
Managed to get a board into a state where it had only data pages and no swap pages, and therefore fds_init fails with the NO_SWAP...
I want to use nrf SPI driver for SPI flash implementation. For that want to send either SPI transmit or SPI receive at single instance to write or read flash address. But...
Version: Mac OS X 10.15.5 (19F101)
I'm using the nRF Connect app Getting Started Assistant and manage to get through most of it. However, when I use Segger to open up a...
