Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi, I am going to use the nRF91 DK to program an external PCB with the nRF9160 on it. The DK documentation says that only 1.8V or 3.0V is supported for external debug/programming...
I am running on a Windows 10 PC.
I've downloaded and installed all the tools for the nRF9160 DK using nRF Connect.
After installing the Segger Embedded Studio, I followed...
Parts of this discussion started on this thread: i-am-trying-to-do-dmx512-protocol
I am using SDK 15.2.0 on an nRF52810. My test board is based off of a Laird BL651 which...
I am trying to setup SEGGER Embedded Studio to program the nRF52840 dongle hardware. I followed the Getting Started Assistant program to set up the development software for...
The SDK version I am using is V15.0.0.
I use the function interface nrf_gzll_set_pa_lna_cfg 。 The following is my configuration information：
static nrf_gzll_pa_lna_cfg_t...
Hi dear community,
I am currently using nRF52 DK which has 52832 on it. I am using it for my bachelor thesis project and want to create simple sensor network. I am using...
Dear,
I am using nRF9160 DK,
firmware: secure_boot & AT_client
and Tale_SIM from Telia, I want to get the current GPS position by AT command?
Is it possible? Which...
Hi,
In a design which should be compatible with the NRF52832 we want to use the NRF52840. As the NRF52832 doesn't have USB, this would mean that the VBUS and data lines...
I am confused because i see documents referring to cmake/ninja and west. Recently it looks like people are suggesting to use west with master branches. Can someone definitively...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10 .My testing master device is cell phone(Huawei HTC and so on,android system),and using...
Hi
nrF52840 SoftDevice S140 - What is the max ATT_MTU size supported? 244 bytes?
Is there any allowed number of packets per connection event that can be transferred on...
Hey, I just got this nrf52 board with pca10040 and tested few Nordic's examples, which worked just fine. I want to simply put some sine wave signal to one analog input and...
Hello all,
I'm working on a device using nRF52832, interfacing to another microcontroller. I was seeing higher than expected consumption, so started to reduce code to find...
Hi
I just downloaded the nRF connect v2.6.0 - Programmer, but i don't what i have to do to start writing the code.
I only get 2 ``Boxes``, and one of them is called File...
