Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Please answer some questions below.
“Application” and “SoftDevice” can be replaced by DFU, correct?
Is Nordic DFU function inside “Module” (Orange colour part)?
If...
Hi
I am working on a product where I need a battery optimized beacon receiver - the opposite of what yo normal see with a beacon device where it is the transmitter which...
Hello,
I am currently using the sdk multiperipheral example. I use a nrf522832 as a central device and two nrf522832 as peripherals. I am connected to the two devices at...
I'm trying to make i2s working on mbed os by using NRF52 development kit board (based on nrf52832).
Looks like I'm missing something. What I managed to do so far is:
...
Hi,nrf52832 entered in bootloader mode.as ld5 led is keep blinking on power reset and holding if boot/reset button.please help me to get board back to normal mode.thanks.
HI,
I am working on NRF52832 SOC. with SDK 15. where i need to read the SENSOR data from twi protocol.
Common Write and Read Register function has been created
I...
Hi,
I would like to use the Raspberry Pi and the Thingy:52 as published in the demo. My question is, how many Thingy:52 devices are supported by the demo?
I have a nrf9160dk I followed the steps in the movie www.nordicsemi.com/.../GetStarted I have inserted my own sim that is working in my phone but I do not get LED3 and LED4...
Hi There
Is there any additional drivers that i have to install to use nRF connect on my Mac?
I've installed it and when i connect the nRF9160 DK to the Mac, it doesn...
Hi, I am trying to implement app_timer library with FreeRTOS. Based on my testings, it seems that app_timer_start() under app_timer_freertos.c has the lowest time resolution...
Good day
I moved from Mesh3.00 to mesh 3.1 and I see the way UUID is extracted is slightly different.
I would like to know when I copy the UUID to use in my project will...
Sorry for disturbing!
I have some questions about measuring nRF52832 32Mhz Crystal frequency.
I use an active probe(Tektronix P6243) to catch the signal and the test result...
In the case where connecting to a phone that is paired with my device after my device has cleared pairing information and doesn't remember the pair, I'm observing the following...
I'm working on a project to get two devices to agree on a secret key based off of physical layer properties.
My solution is for devices A and B to make 64 RSSI measurements...
