Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
In nrf52832 datasheet, it uses" 64 MHz crystal oscillator, using external 32 MHz crystal "
then, can I use external 16 MHz crystal or external 4 MHz crystal to drive nrf52832...
I couldn't find nrf_drv_timer.c file. I want to create timer so I try to different SDK for my work. I am using SEGGER IDE for prepare software but i encountered lots of problems...
Dear nordic,
I try to build BLE application everything works fine expect the UART. The UART has transmission issue.
it has no problem in receiving. but when i tried...
Hi,
I am using nrfMesh2.2 SDK. I want to add models other than GenericOnOff and configurationclient to the interactive_pyaci. How do we proceed with this?
I found the utility to create the binary image of the production data for my Zigbee device but cannot find any documentation on how to incorporate the generated BIN file into...
Hi,
I have a custom board with nRF52832 and I'm using SDK 13.1 and softdevice s132 4.0.5. I have a GPRS module that I will use to receive the new firmware image and I will...
Dear Nordic,
I installed nrfConnect 2.6.1 and lauched "BluetoothLow Energy" application. Then i selected my board and it asked "Device must be programmed ..." and loaded...
Hi There,
I'm interested to customize the eddystone TLM parameters as per the image below, which is replace the Battery voltage with Button detection On/Off.
I did...
I was able to successfully make the BLE Peripheral Eddystone Beacon Application in "nRF5_SDK_12.3.0_d7731ad" in Windows 7 32-bit (pca10040), using GNU Tools ARM Embedded version...
Greetings,
I'm fairly new to developing with Nordic ICs using the SDK, I have previously developed for some nRF51x MCUs using some modules that had an Arduino library...
hello , everyone
platform : NRF52832, SDK13.0 , project:\examples\ble_peripheral\ble_app_template
I meet such a problem, config app_timer in APP_TIMER_MODE_REPEATED and...
Hi,
I cannot get the interrupt on Timer1 to work. I have checked that the counter is matching the compare register by not enabling the interrupt. When I enable the interrupt...
According to the official suggestion circuit, I’ve deleted some functions which are useless for me, (the schematic circuit diagram and PCB are showed in the end) then I use...
Hi all
I'm using nRF52 DK with 14.2.0 SDK. I created a LED blink project for testing and extract its HEX file. I uploaded the program to the nRF52 over USB (J-Link-Keil...
