Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
Hello,
I'm running both central and peripheral roles for BLE on Zephyr, along with UART and some GPIOs.
SDK: 2.6.2
The project includes MCUboot, supporting DFU...
We are trying to max out the wifi throughput via nRF7002 when connected to SPI4. Currently we only achieve around 6.3Mbits/sec (TCP Upload to peer).
When measuring the SPI4...
I have a custom board, with nrf5340, nrf7002 on it.
I would like to get the uA levels of power consumption I see other nrf5340 projects talk about (eg here ) when my application...
i have connected usb type(b) to j3 and kept the switch to usb but no advertsing happens and i have also connected external supply 3v to p21 the board is not on . only while...
Using Zephyr in NCS 2.8 on nrf5340/nrf7002 wifi combo, and trying to get https to work. I'm using the option where the TLS setup is done in the socket layer (enabled in prj...
I’m trying to set up a simple relay using an nRF52840 board to route data between a BLE central (my phone) and a 9600bps UART device. My goal is to send data from the phone...
i've captured the following using a joulescope js-220 as an inline current meter across the VDDM CURRENT MEASURE jumper on my rRF54-DK board....
i'm running the system_off...
Hi!
I'm storing a key in the KMU for use by the ECB.
If I set the slot's destination address to an address in RAM, the KMU pushes the key there correctly, but if I instead...
Hi,
I have a custom board, i enable the adc peripheral, and it generates:
then i connect the AIN4 channel and it generates:
but when i build i get the following...
Hi, I'm looking to develop an out-of-tree driver for the SIM800L modem. The reason I want to develop it out of tree is that I don't believe have the skills or resources to...
HI
I previously disabled DCDC in the app using the following method:
in app.overlay
I am using ncs 2.9.0 I saw some posts using CONFIG_ENABLE_DC_DC=n , but I am unable...
Hi,
I'm try to set up a UDP server on a nRF9151dk, and send data from a remote pc to the devkit. I have tested my sim and networking works correctly, I am able to use coap_client...
Hi,
I am using the nPM1100 in my new application, where the system power circuit includes two additional 250mA LDOs configured to provide a 3.3V output . I am also using...
Hi,
I am encountering the following build error with the BLE peripheral example after migrating from NCS 2.7.0 to 2.9.0 and when CONFIG_BT_LL_SW_SPLIT=y is set in prj.conf...
