To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
I just migrated from MacBook Air with M1 processor to MacBook Pro with M3 processor. I installed VS Code and nRF Connect SDK v2.6.0 from scratch on my MacBook Pro. hough my...
Hi，
I followed the steps below and the error "zephyr\zephyr_pre0.elf section 'text' will not fit in region' FLASH'" appeared when I compiled. I did not change any code....
Greetings team,
We are using the nRF Connect for Desktop v4.4.1 and Programmer tool has been updated to v4.3.0
Using this version the MCUBOOT settings are unable to turn...
Hello, I try to config vendor id and product id according to https://docs.nordicsemi.com/bundle/ncs-2.0.2/page/nrf/ug_matter_configuring_protocol.html .
1) When I change...
Good morning,
I work with the nRF52840DK board and the BC840E and I would need to make some changes to the SW of the "radio_test" application, but trying it out I find it...
Hi,
I am going to consider NRF52811-CAAA in a design. Can you please help with these questions:
1- What is the expected End of Life for NRF52811-CAAA chip?
2- If I have...
Hello,
We have a custom board for nRF52805. We have one LED connected to the GPIO. I wrote the FW for Blink LED every second.
I build the FW using the command " west build...
Hi,
I encountered a very strange issue. We are developing the firmware using v2.6.1 SDK and using Visual Studio Code + Nordic plug.
Platform: nRF7002-DK
SDK: v2...
Hi everyone,
I am currently experimenting with the NRF7002 WiFi stack and Zephyr. I want to build a Wifi bridge from my Bluetooth mesh network. I do have some experience...
I am following the nRF Connect SDK Fundamentals and an issue with vs code at the fund_less3_exer1. Vscode doesn't seem to locate the header files of my project. It does seem...
Hi,
Is there a way to use the nRF700x 5.8 solution to access the low level PHY layer such as with the nRF58240 part number.
I would like to use this companion chip for...
Hello,
I am starting to test the sample "https_client" on nrf9160 and expected to see it working (through LTE modem)
The execution hangs on the line k_sem_take(&network_connected_sem...
- The product I am making uses nRF52833. In addition, the audio part of Thingy 52 was added to the product as above. (The speaker uses 1.5W, 8ohm. Current consumption is about...
Hello! Can you please clarify the capabilities of the Nordic platform, I am interested in the following topics: 1) Out-of-box BLE co-existence support (possibility to run...
