I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
HI
My current system consists of an nRF54L15 paired with an external flash and sensor. In low-power mode, the current consumption is approximately 15 µA. After sleeping...
Hello! I am facing issues when trying to set up a PPP connection using the Serial LTE Modem (SLM) application on the nRF9151 DK, and I would appreciate some guidance. I am...
Hello,
I have seen many topics regarding the SAADC sampling modes and power consumption trade-offs on DevZone, but none of them clearly address my concerns. I would like...
Hi there,
We are currently developing a system, where around 480 kbytes of data are transmitted over BLE. Throughput is supposed to be as high as possible.
We are using...
I have a school assignment revolving a technological product, where i need to ask a few questions to a business about their involvement with the product. Therefore i need...
I set the voltage at the PPK “Source meter” to 1250mv, and then used a multimeter to measure the voltage between the PPK “vout” and “GND”, which was 2830mv. How can this situation...
Hi,
We're working on a cellular design using the nRF9151 with an nRF7000 for location finding. We have a working prototype on the Thingy91x and are currently focusing on...
I was reviewing the Large scale Bluetooth mesh testing - Blogs - Nordic Blog - Nordic DevZone and noticed the statement: " Initialize the network by flashing the test firmware...
I want to connect Waveshare E-ink display to nRF5340 using e-Paper Driver HAT. At first, I tried to make all the calls by my own, just by rewriting the code from the ESP driver...
I am attempting to use the COMP section to build a relaxation oscillator. There appear to be a number of interactions between sections, some of which are subtly documented...
Hi there,
I went through all the documentation and instructions in order to use my nRF52DK as a sniffer and I can not see it in the capture devices in wireshark.
am not...
1. What versions of GSMA specification does nrf9160-SICA modem support? In particular we are interesting in SGP.02, SGP.22 or SGP.32 versions.
https://www.gsma.com/esim...
We are developing a Bluetooth peripheral device.
The peripheral has no input/output capability, and a fixed passkey is pre-programmed.
We would like the pairing to succeed...
On the Online Power Profiler I noticed changing iDRX interval has a significant effect on power consumption. How can I adjust this interval on our device?
I saw this ticker...
We want to be able to see if Proprietary PSM is working to determine if our device should reduce uplinks to save battery.
Is there a way to show that the Proprietary PSM...
