We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
I am working on adding MCUboot to my custom board (using nRF52832 chip) to make it DFU-able. That works fine when using internal flash but never when moving the...
Hello, I'm using an nRF9151 DK with an SPI attached SD card and SDK 3.1.0.
SD card is accessed using FAT_FILESYSTEM_ELM.
Using a single thread approach everything is working...
Hi,
We are using a TMD2636 proximity sensor on our board, connected via I²C on pins P0.18 (SDA) and P0.30 (SCL). The same I²C bus also contains a TMP117 temperature sensor...
Hi,
I’ve enabled OTA firmware updates in our project using MCUboot. Before enabling OTA, everything worked correctly—our firmware received interrupts on pin P1.00 from one...
After reviewing the nRF7002 datasheet and reference design guidelines, we were unable to find the input/output characteristics and voltage ranges for PALDO, VDD_BUCK, PWRIOVDD...
Current Setup
I'm currently setting TX power during advertising using the following code:
This successfully sets TX power during advertising, but I need help with additional...
I have been reviewing the datasheet of the BLE audio nRF5340. It lists multiple power rails in power section.
Is any power-on sequence required for the SOC.
Also, can...
All of the following used the same power supply to power our development board and measure the current of the development board: The PPK2 I purchased measured an average current...
Hello,
I have connected the nRF52840 DK to the nPM1300 EVK , with the DK powered from BUCK1 output of the nPM1300.
When I supply 3 V or higher to the VBAT pin of the nPM1300...
Hi,
I’m evaluating the NUS (Nordic UART Service) as a way to stream and receive byte arrays.
I’ve noticed that there are two different implementations of the NUS service...
Affecte d SDK : n RF Connect SDK v 3.2.0 (Zephyr v 4. 2.9 9)
File : z ephyr/drivers/i2c /i2c_nrf x_twi.c
Description
The I2C TWI driver always returns - EIO for every...
I have been reviewing the datasheet of the BLE audio nRF5340. It lists multiple power rails in power section.
Is any power-on sequence required for the SOC.
Also, can...
Using NCS 3.1.0 - getaddrinfo with "offloaded sockets" (nrf9160/51) and ipv6 results in struct sockaddr_in6, where some "c struct padding bytes" (the last 3 of 24 bytes) are...
I flashed the thingy91x using NRFCloud connect. Provisioned it in nrfcloud using hologram SIM cards. How do I turn on air quality and all other sensor information?
ZBOSS NCP: ZBOSS NCP Serial Protocol, Version 1.5 states that a "Full featured Zigbee PRO r22 platform is provided".
Is a more recent version of this document available...
