I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
I have done a clean install of the SDK on Debian 13
I have nrfutil install and its working fine - i have tried installing both the v3.2.1 and v3.2.0 toolchains and in both...
Hello Nordic team,
We are using the GRTC on the nRF54L15 , and we are observing the following behavior:
When MCUboot is enabled , the GRTC (likely backed by SYSCOUNTER...
Hi, I am using nrf9151 as a modem running SLM. When SLM comes up, it throws this error. This is a new board run and 50% of the boards show this issue.
I appreciate there...
I am looking for a pairing between Windows laptop or Android mobile on the transmitter side and hearing aid which has bluetooth streaming features as a receiver..
I am looking...
Hi there,
Is it possible to have the DECT NR+ modem trigger events via DPPI? For instance, I'd like to capture a Timer value *exactly* when nrf_modem_dect_phy_time_get...
Hell ,
I am planing to use nRF52810 for one of my mesh application,now query is
How much power consumption its will take when RF is disable and listening only external...
Hi
We use nRF5340, set GPIOs as PDM for DMIC device, and measure waveform as below
The PDM DATA high level will decrease periodically
Is this waveform normal? If yes...
Hi,
I know that pc-ble-driver-py is archived but as there is no real alternative to it, I'm still using this package...
I'm using BLE nRF52840 dongle to connect to...
I am using the nrf52833 with 17.1 SDK and s140_nrf52_7.2.0_softdevice，i want to scan a scannable extend adv packets，
This is what i get in the BLE_GAP_EVT_ADV_REPORT ： ...
# Background
I am attempting to install ble-sniffer onto WireShark for BLE sniffing. I have been following the guide in Link. I have already flashed my nRF52840 USB dongle...
Using Thingy:53, I needed to add the following code to the boards/thingy53_nrf5340_cpuapp_ns.overlay file in order to be able to view the output:
&uart0 {
status="okay...
Hi
We measure I2C SCL falling time is 5.87ns, little faster than spec. 6.54ns ( 20*1.8/5.5)
We use PIN_CNF[n] (Address offset: 0x200 + (n × 0x4)) ID D drive to tune, but...
Hello,
Are there schematics available for the nRF9151DK?
In the hardware ZIP file, I can only find the BOM and PCB files (PcbDoc and PrjPCB), but no schematic files or...
I want to design a pair of TWS speakers using the nRF5340, but I'm having a hard time figuring out where to start. From what I understand, the unicast server nRF5340 audio...
