I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Summary: My custom board with an external crystal is consuming 208 µA when powered down under Zephyr, and I need to reduce it to less than 20 or so.
My board is based on...
Hi,
I'm working on a project trying to build a simple application on my own customize board with nrf52833 SoC.
After the configuration to my own board(Leds, button GPIO...
I'm attempting to store log data on my nRF52832 using the little file storage, and then allow a client to access this over BLE. From what I can tell, the data transfer can...
Hi,
I am using device nRF51822-CFAC, the SoftDevice is S130_nRF51_2.0.1(Id: 0x0087). In my project's General Options->Target->Device, I selected "NordicSemi nRF51822-CFAC...
Hi,
Could help me please?
What I need?
1) set GPIO pin as input with internal pulldown and set IRQ for Rising Edge.
In .overlay I add my pin like that:
Then in...
Happy Friday! So, I've fully funded on Indiegogo and now I'm in the application development stage. I'm new to development but I'm trying to build this app myself.
So far...
Hello, I have a need to include a header file that I have defined in one of the Connect SDK .c files. For the purposes of this question, let's say I want to #include "myfunctionsandvariables...
I recently bought a pca10059 and inadvertently erased the bootloader while using a script from another project.. (it did --recover unfortunately).
I'm using the debug out...
Hey Nordic team ,
We are trying to work on use-case where we want NRF52840 to generate thread Stack message but instead of using multi-protocol features it can transmit...
Hi,
I know nrf52840 does not support direction finding and it seems because of hw limitation like the link.
But can I get a little more detail why nrf52840 can not...
Hello all,
Currently, we are using the nRF52840-DK and realized that the interface to upload programs is very handy (being able to simply drag a .hex file onto the device...
Hi,
after updating my NCS version to v2.1.2 I noticed that my Zephyr SDK also needed updating from 0.14.1 to 0.15.1. However, after updating my Matter project does not compile...
Hello,
When using two nRF52832 modules for Bluetooth connection, can it prevent Dos attack program? We have found a situation where a malfunctioning or malicious client...
Hi,
I am evaluating the nRF5340 Audio DK and measuring while adjusting the audio bitrate.
I found the following 3 symbols definition for bitrate.
CONFIG_LC3_BITRATE...
