Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
It is found that under the same routine in zigBee SDK, the project under pCA10056 folder can run normally without burning the protocol stack, but the project under PCA10059...
We would like to stream data through an l2cap channel from a nRF52840 module to a smartphone. The l2cap connection is initiated by the smartphone, I configured an l2cap tx...
I would like to test some compatibility features using the nrf52833 DK as a Bluetooth 4 transmitter instead of Bluetooth 5 (which it is by default). I do not see an explicit...
hi support team，
i have two questions from customer.
1. Monthly review suggested that Verizon certificate will be on October this year, how about he progress, we have...
I'm using the Nordic UART Service to implement BLE communication between an iOS app (central) and a Raspberry Pi (peripheral). Whenever I send a large payload to the central...
Hi,
We are using Nordic thingy 52 HW and their SDK for our Evaluation purpose. We are using Nordic thingy 52 microphone code directly. That firmware is using ADPCM codec...
Unable to connect to Bonded weara with GATT 133 error. Currently, there is only one solution, turning on and off Bluetooth in the OS, which temporarily improves the connection...
Hello
new nRD5 SDK v17.1.0
Can you please help me to find more about:
1. "- NRFFOSDK-13484: Added an option in the Peer Manager to decide that a connection will not...
Hello,
I am currently developing an application on a single core application. I need to add a BLE part to this application. Currently, I have an OTA update procedure that...
Hello,
I'm trying to open an L2CAP connection and send some test data to the nrf52840 dev board from my computer. But my connections were timing out with 'Page Timeout'...
Hi ,
I have a question ,according to the official configuration and example, the ADC sampling voltage value is smaller than the actual voltage value. For example, the actual...
I have nrf52832 dk and soft dveice s132 am using ble app template code.
I need help in this code that as:
1. as i flash the code on dk, the device should be initally in...
I am using NCS v1.7.0 and have found that SES is not being configured properly for debugging/flashing. When I open the project in SES, building works fine, but when I try...
I have a theoretical question involving 6 24L01+ devices in PTX mode and one 24L01+ device in PRX mode.
Assuming a synchronized system, when one PTX finishes transmitting...
