Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hello,
I'm evaluating nrf52840 and trying to use zigbee/light_bulb as a starting point. One thing I caught immediately and still trying to find an explanation for was the...
Hi DevZone,
I need help to understand the DFU procedure over the Mesh without any second BLE dongle/BLE serial device to populate the DFU packets.
The ask is how can we...
Hi
I am using the nRF52840 with an external sensor which I need to config (nRF is the master). after this, nRF is acting like a I2C slave (twis) and i like to trigger an...
Hi,
I'm making my own program to upgrade the nRF9160's modem firmware over SWD. So far, application note nAN41 has helped a lot, but I'm getting stuck when trying to get...
Hello.
I need to transfer files from a phone to a BLE peripheral device. I have a small FatFS filesystem on an external flash chip on the device, and I'm now trying to decide...
Hi,
I have just setup the nRF Connect SDK for the first time. I am running Ubuntu 20.04 in a Virtual Machine. I followed the instructions in the "Getting Started Assistant...
Hi!
I'm trying to prepare FOTA firmware using instructions provided by: FOTA upgrades but it seems not working.I have couple of issues and questions. Please help me.
My...
Hello,
I have been experimenting with the new VSCode extension for the last week or so and I've noticed some issues. I understand that this is a currently a beta release...
Hello,
Is it possible to receive a review for a board i'm developing??
This board is to be used as a Raspberry Pi Hat to be able to communicate using UART between RPi...
How to recover communication due sequence number. (Could be due of PYACI serial hardware changed/dammaged). Is there any command to reset or know sequence number of node....
Hello all,
I'm developing a BLE CGMS application based on the experimental example on the SDK folder.
Now I working in the timing characteristics and I could see that...
It looks to me like there's usage of the 32 bit milisecond timer in the mqtt client.
It seems to me that mqtt_elapsed_time_in_ms_get(...) could calculate an incorrect elapsed...
We're using the nRF9160 with an external main microcontroller, and communicating with it over SPI. We're evaluating the lowest power modes of our custom hardware to make sure...
1. I want to minimize current consumption (5uA - 10uA) in nrf52832.
2. We are using the soft devices in it.
3. Please tell me all possible SDK configuration settings for...
Hello all,
I have a BLE central application based on nRF Connect SDK V1.6.1 and a BLE peripheral application based on nRF5 SDK 17.1.0. The peripheral wakes up on interrupt...
