Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
NCS(nRF Connect SDK) is a good environment to develop nRF52,but it seems not stable until now.
I want to use NCS(nRF Connect SDK) to develop my project ,and met some unknown...
Hi Supporter,
I use apptimer in proprietary_rf gzll, I used as below ,but it doesn't work.
1) app_timer_init(); ,here I ennable the RTC1 in the sdk_config.h
2)app_timer_create...
Hello NRF ,
I have been using NRF9160 DK GEN-1 board for NB-IOT and GNSS tracking and able to configure my network SIM as well as the NRF cloud .
I have used SDK 1.4.2...
Hello There,
Basically I just want to get Sensor data like (Temp Sensor) who already connect to Arduino and I get it , So I just want that data to nRF9160 over UART in...
Refer to nRF52840 Technical Manual USB 2.0 (full speed (12 Mbps) controller) The USB2.0 rate can be up to 480Mbps. We have a product whose USB transmission rate must not be...
I have created a program code on the Adafruit nRF52840 express in the Arduino IDE. I want to read this program code (including bootloader) via my j-link edu mini and save...
I noticed that the nRF Connect SDK has kept up with ZBOSS updates throughout the year. Is there a plan or recent releases with regard to the "nRF5 SDK for Thread and Zigbee...
Hi! I'm working on a custom board with nRF9160, I want to flash it with the asset tracker sample, however, I do not own a J-link device. What I have is a FTDI USB-UART converter...
My Thingy:52 is version 1.01. I haven't used it for a while and after charging, it didn't seem to be advertising. It was soft-flashing a green LED. I decided to program it...
Hi,
i am working on nrf52dk. i want to include "pwm" example in "ble_app_uart" example . i have included all the header files. and functions in "ble_app_uart" example. ...
Hi,
what is safe temperature range for nRF52840 - nRF9160 UART communication on 115200 baudrate without external crystals for HF clocks please ?
Thank you.
Hi,
I'm trying to program a custom board with a nRF52810 via nRF Connect. I keep getting the following error messages:
I followed this post and tried the following commands...
Hey guys,
I have nrf52832 custom Bluetooth module. It is stand alone nr52832 module . I just want to toggle any gpio on this module .
Can you guys tell me which library...
Hi all,
In my project, I make 2 SPIM and 1 UARTE works well.
Currently I want to use 1 TWIM, so I add lines below in proj.conf
However, I get errors: gen_isr_tables...
