Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
I want to upgrade my application from v1.4.2 to v.1.5.1. but the Bluetooth init failed. So I tested with the scan_adv, which uses the same logic as my application. This also...
The device communicates okay with JLINK commander v7.00a although at the beginning it always says "Connecting to J-Link via USB...Out of sync , resynchronizing... J-Link communication...
Development Environment: icore7 laptop running Ubuntu 20.04.2 LTS.
Target: To build connectedhomeip sample application for arduino nano 33 ble board and check against laptop...
Hi,
We are building our project with nRF52811 and Segger Studio V5.34. (I have Ubuntu 1804 if it helps.)
We have certain variable configurations but would like the ability...
Hello Team,
My end goal is to send 0 to 600hz signal over Ble using NRF52832[ as explained below image].
So, for this, I have used this GitHub code
https://github...
Hello,
I am working an a product based on the NRF52832 and I need to trigger an interrupt when a capacitive button is pressed / proximity detected (BLE is peripheral and...
Good morning,
I'm starting to develop an application for the nRF52805 using ble_app_hrs_freertos as a base.
The modification I did are:
Ported from nRF52832 to nRF52805...
Hi,
I am developing a beacon scanner on NORDIC Thingy 52 using Nordic thingy52 SDK, Now I want to add NUS(Nordic UART service) in my code to send data to the client(ESP32...
I have successfully built the Dynamic Multi-protocols network with Thread and BLE, and used Raspberry Pi 3B + as Gateway Now I want to integrate more AI into the system, but...
Hi there!
I have a host microcontroller connected to the nrf91. The host microcontroller will enabling the nrf9160 through the enable line. From the documentation, VDD_GPIO...
Hi.
The Zigbee stack used in the SDKs automatically stores the network data in the Flash. I know it is possible to erase the NVRAM data with ERASE_PERSISTENT_CONFIG to...
I'm having trouble incorporating the FatFs library into my existing project. I've used CMSIS to update sdk_config.h I've added diskio_blkdev.c and ff.c to the project. When...
Hi all,
I am wonder is there any way to broadcast data using asymmetric encryption algo or digital signature? As I want to encrypt my data using a key and other device...
Hi.
I have got an Iphone 12 and installed nRF Connect. I cannot see the MAC address of connected device. That was possible on my old Android phone.
Does anyone know why...
Hi,
I am using nrf9160 to communicate with LIS2DHTR.
I use I2C_2
In file nrf9160dk_nrf9160_common.dts in ncs\v1.4.0\zephyr\boards\arm\nrf9160dk_nrf9160
&i2c2 ...
