Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
I used the timeslot function of the nrf52832, but when I called the radio to send data, I found that the signal strength was very weak, much lower than that of BLE. This resulted...
I am using nRF9160 DK with nRF Connect SDK v2.9 and the LwM2M client sample ( /samples/cellular/lwm2m_client/ ) , converted from PSK to X.509 certificates .
The device connects...
In the software development for the nRF52832, the SEGGER_RTT_printf() function is called throughout the code for debugging and problem analysis.
Would there be any particular...
Can I copy the ESB code from SDK v3.3.0-preview3 into SDK v2.9.0, and then get the functionality in esb_ptx_ble & esb_prx_ble?
Is there any way to achieve it quickly?
Hi,
I am working on a project with two nRF52840 devices (nRF Connect SDK 3.2.4 / Zephyr RTOS) that are already connected via BLE. On top of the BLE link I need a low-latency...
Hello,
I need to measure current consumption on the nRF52805 in sleep, TX, and RX modes. Which sample applications are recommended for each of these measurements? Additionally...
Hello,
I am facing issue in reading the eDRX mode configurations using AT Commands on nRF9160. Below are the details of hardware & modem fw version.
1. Modem FW version...
What is the recommended way to clear the retained LATCH register using the zephyr generic GPIO functions after waking on interrupt from system OFF? It does not appear to be...
I have designed a custom PCB using nRF54L15 SoC and have gotten it verified from Nordic people. I will share the gerber here as well. I am using VS Code for flashing the code...
# Console disabled - uart30 used exclusively for MCUmgr SMP
CONFIG_SERIAL = y
CONFIG_CONSOLE = y
CONFIG_UART_CONSOLE = y
CONFIG_PRINTK = y
CONFIG_LOG = y
CONFIG_MAIN_STACK_SIZE...
Hi everyone i have a problem with building a project, i dont know what i did wrong, before everything was building fine, but now if i pristine build any project some lines...
Hello,
My application crashes with a Kernel Panic (ZEPHYR FATAL ERROR 4) during NFC communication :
ASSERTION FAIL [ header.ctx_size <= 16 ] @ WEST_TOPDIR/nrf/subsys...
Hello this is my first time designing nrf series. and i want some feedback of my board design and rf circuit
Thanks in advance for your time and suggestions.
these are...
Hello,
I purchased my first nordic semiconductors device, the PPKII, from Farnell.
I just received it today and installed the required software (nRF Connect on macOS...
