Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello,
I'm trying to use the ble_db_discovery module to collect characteristic UUIDs and handles for two services on the same node, with the same connection handle. I first...
I have a device that uses the Nordic UART Service (NUS) to provide a serial port like interface to my product. Now I need to start working on the PC side of the system. The...
Hello,
I am using nRF52840 S140v7.0.1 and we are going for certification. I am bit confused with Bluetooth core version mentioned in Nordic certification and website....
hello Support team,
with asset tracker examples, seems not able to connect to nrfcloud recently with NB-IOT network.
do you know what is the reason?
Best Regards...
Hello,
I open the project :
I want to flash the basic application asset_tracker to my Thingy 91 after I built it from Segger to be sure everything is set and working...
Hi i was trying to add nrf calender part which i found in git hub for nrf52 chip with ble app uart example, but when i nrf_sdh_enable_request() called to initialize ble system...
Hello
I want to install the nRF Connect SDK (v3.4.1) on my Linux Elementary OS 5.1.6 Hera to use the nRF9160 and the Thingy91 later on. I've installed the toolchain and...
Hey,
I am working on S130, nRF51, been working for a long time with DFU and it was fine both using nRF Connect and nRF Toolbox
Lately I changed my workstation and so...
Hello everyone I am trying to program my dongle with the Dk Following this schematic :
When I press the reset button on the dongle, the led start pulsing in red.
I am...
someone that can give me a datasheet of this microcontroller (i think) i searched the hole web and don't find one in specific, the one i found are different in the last line...
Hello, I am working on low power modes of MCU M33 core in nRF9160 SOC.
From the document of nRF9160 product specification v1.0, understood that there are two low power modes...
Hello,
I am trying to capture the advertisements of the surrounding BLE devices with NRF52840 Dongle using pc_ble_driver_py python library. I am successful in capturing...
I am working on third party module RAYTAC MDBT50Q-DB with nRF52840 with SDK V17.0. I am trying to run ble_app_interactive example on it but just can't get it done. I have...
