Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
We are aware that i2s internally includes hardware double buffering to ensure that the audio is continuous.
Is there any way by which we can avoid double buffering...
Hello,
I developed board with NRF9160 chip and I am facing issue with "at_cmd: Failed to open AT socket (err:-12)", i am not able to communicate with modem. It is not...
Hi
Can I not modify the param the radio project example,and let it run on IEEE802.15.4-2006?
and the demo example run on 2.4GHZ?
I modified two params:
NRF_RADIO-...
Hello,
I'm using nRF52480 Dongle. I executed an Erase All from SEGGER Embedded Studio. My project still works but the LEDs are not blinking anymore. The only way I can have...
Hello nRF Team,
we are using nrf51822 for one of our product. We have implemented firmware update functionality using a secure bootloader library.
After loading the soft...
Hi, I want to distinguish whether the USB is connected to a PC or a power adapter.
For my application, FATFS still needs to work when connected to a power adapter, so it...
Hi Nordic,
Why I cannot directly use segger's "Build and Debug" to download file to nrf52832, after I modify some code?
After I use nrfGo Studio first to program the...
Hi, in the past, there has been discussed several times whether a peripheral can advertise even when it is already connected/bonded. It turned out it could be possible, however...
Hi, We are working on multiple product based on different MCUs (nRF52832 and ESP32). We would like to use the same Nordic BLE DFU for both of the products so that we would...
Planning to run Packetcraft LEAUDIO stack on nRF52840-DK. This is for evaluation and later on for some development on top of it.
Will it be supported. or is it must to have...
Hi,
I am trying to figure out how serial handling works. Specific questions bolded below. To the best I can see, what I think happens when transmitting is:
NRF_SERIAL_DRV_UART_CONFIG_DEF...
Hi,
I have custom board based on nrf91 but i am going to generate 2 SKUs out of it, the first board consists SIP alone mostly running the SLM application, and my second...
I am trying to capture a signal that transmits upon receiving a polling signal along the same wire.
I have frequented this example but still not having any luck (LED toggles...
Hi,
we have in production an old application developed with SDK13. The application size is growing and with the last update we discovered that during DFU bootloader update...
Hi
I am using an Analog Devices chip as a SPI master and BMD350 (based on nRF52832 chip) as a SPI slave. I want my phone app to send command to the BMD 350 (SPI Slave via...
